Manuals / Icom / Marine Equipment / Marine Radio

Icom IC-V8 Entering set mode, Repeater tone frequency, Tone squelch frequency, Dtcs code

Models: IC-V8

1 68

Download 68 pages 36.59 Kb

Page 55

OTHER FUNCTIONS 11

‘Set mode

DEntering set mode

qPush [8•SET] after [A•FUNC] is pushed. w Push [∫] or [√] to select the desired item. e Rotate [VOL] to select the condition/value.

•To exit set mode, push [#•ENT ].

DRepeater tone frequency

Selects tone encoder frequency for accessing a repeater, etc. from one of 50 available fre- quencies.

• 67.0–254.1 Hz (50 tones): 88.5 Hz (default)

DTone squelch frequency

Selects frequency for tone squelch or pocket beep operation from one of 50 available fre- quencies.

• 67.0–254.1 Hz (50 tones): 88.5 Hz (default)

DDTCS code

Selects DTCS encoder/decoder code with po- larity (N: normal/I: inverse) from one of 208 available codes.

• 023N/I–754N/I: 023N (default)

DOffset frequency

Sets the offset frequency for duplex (repeater) operation within 0–20.00 MHz range.

DReverse function

Turns the reverse function ON and OFF.

• Default: OFF

F

MR

F

MR

F

MR

F

MR

F

MR

TX

TX

DTX

TX

TX

46

Image 55

Icom IC-V8 Entering set mode, Repeater tone frequency, Tone squelch frequency, Dtcs code, Offset frequency

Contents

IV8 Safety Training Information Page Foreword Supplied Accessories Precaution For USA only Table of Contents Scan Operation Cloning 13 Optional Unit 14 Specifications 15 OptionsMemory Programming Dtmf MemoryMicropho ‘ Switches, controls, keys and connectorsPower Switch Power PTT Switch PTTSP/MIC Jack Squelch Switch SQLAntenna Connector UP/DOWN Keys Y/ZKEY Function Key padPanel Description Key pad Panel Description ‘ Function display 0LOW Power Indicator Signal IndicatorAntenna ‘ Accessory attachmentBelt clip Battery Packs ‘ Battery pack replacementRecycling information U.S.A. only ‘ Battery cautionAbout AD-99 ‘ Battery chargingDRegular charging With the BC-146Rapid charging with the BC-121+AD-94 #11 Rapid charging with the BC-144‘ Charging Note Battery pack life‘ Battery case optional for some versions Setting a frequency Power onVia the keypad To set the squelch level Setting audio/squelch levelBy other methods To set the audio levelReceive and transmit Selecting call channel Selecting a memory channelKey lock function Display type Using Initial SET ModeGeneral About reversed duplex modeOffset frequency Using SET ModeHz Tone Tone informationFrequency Range Duplex Direction Programming the memory/call Channels Memory channel contentsMemory transferring Channel name programmingMemory/call VFO Memory/call call/memory Clearing a memoryOne of d0 to d4 appears Programming a Dtmf codeManual Dtmf code transmission Using a Dtmf memory channelTransmitting a Dtmf code Transmission speedPriority memory channel watch Scan typesPriority memory channel scan Programmed scan Memory skip scan Setting skip channelsMemory or call channel watch Priority watchMemory scan watch Scan resume Condition Recommended tone frequencies OperationAvailable Ctcss tone frequency list Setting subaudible tones for tone squelch operationWaiting for a call from a speciﬁc station ‘ Pocket beep operation‘ Tone scan PAGER/CODE Squelch Code channel assignment Before programmingCode programming Pager/code squelch operation during channel indication Receive accept/receive inhibitCalling a speciﬁc station Personal Calls Waiting for call from a speciﬁc station‘ Code squelch Dtcs code Entering set modeRepeater tone frequency Tone squelch frequencyLCD backlight Tuning stepScan pause timer Function key timerPager/Code squelch channel Optional UT-108 required Transmission permissionTime-out timer Entering initial set modeKey-touch beep Repeater lock-out DAuto power-offDisplay type Squelch delayDtmf speed Dial assignmentTuning speed acceleration Power saveLCD contrast Optional HM-75A required ‘ CPU reset Cloning using a PC DTransceiver-to-transceiver cloning AT Power onOptional Unit Optional UT-108 installationSpecifications Options Count on us