Manuals / ICP DAS USA / Computer Equipment / Computer Hardware

ICP DAS USA 3-axis encoder card, 2-axis stepping/servo, I-8091 2-axis stepping/servo user manual

Models: 3-axis encoder card, 2-axis stepping/servo I-8090 3-axis encoder card I-8091 2-axis stepping/servo

1 69

Download 69 pages 14.6 Kb

Page 65

I-8091 User Manual

Version 1.0 06/2001

(30)i8091_WAIT_Y(unsigned char cardNo) to wait Y-axis going to STOP state. cardNo : board number 0~19.

(31)unsigned char i8091_IS_X_STOP(unsigned char cardNo) To check whether X axis is STOP or not.

Return value 0 (NO) : not yet stop

1(YES) : stop

(32)unsigned char i8091_IS_Y_STOP(unsigned char cardNo) To check whether Y axis is STOP or not.

Return value 0 (NO) : not yet stop

1(YES) : stop

http://www.icpdas.com

2-36

ICPDAS

Image 65

ICP DAS USA 3-axis encoder card, 2-axis stepping/servo, I-8091 2-axis stepping/servo, I-8090 3-axis encoder card user manual

Contents

Part 2 I-8091 2-axis stepping/servo control card User Manual Part 1 I-8090 3-axis encoder cardI-8090/I-8091 User Manual Version 1.0 06/2001I-8090/I-8091 User ManualVersion 1.0 06/2001 I-8090 ContentsI-8091 Contents Copyright Copyright 2001 by ICP DAS. All right are reserved Trademark I-8090 3-axis encoder card User ManualVersion 1.0 06/2001 Edition I-8090 3-axis encoder card Features8090 Contents I-8000, 4 slots I-8000, 8 slots 1. Hardware1.1 I-8000 hardware address 1.2 Registers of I-8090 board Quadrant Counting Mode counterFig3 CW/CCW counting mode 10 Pulse/Direction counting mode power 1.3 LED Indicator1C 2A I-8090 User Manual1.4 Connection Encoder I-8090 User Manual EncoderVersion 06/2001S8091 card I-8090 User ManualVersion 1.0 06/2001 S8090 card2.1 constants and functions 2. SoftwareConstants Functionsaddress hardware address which defined at chapter 5 unsigned char i8090GETINDEXunsigned char cardNo 4 void i8090RESETENCODERunsigned char cardNo, unsigned char axis7 void i8090RESETENCODER32unsigned char cardNo, unsigned char axis 32 bits encoder counts command sets6 void i8090ENCODER32ISRunsigned char cardNo 8 long i8090GETENCODER32unsigned char cardNo, unsigned char axis2.2 examples 2.2.3 Get X, Y, Z-axis encoder counter’s value case Yaxis 2.2.4 Software 32 bits encoder counter programming #define CARD1 1 #define CARD2 2 #define MAXSLOTNO Show5DigitLed0x04, j value=value/10 j=value-10*value/10 break default int key,ShowAxis i8090Slot=99 for j=0 jMAXSLOTNO j++ Delay5 //delay 5ms case 0 ShowLedValuexvalue,Xaxis break switch ShowAxiscase 1 ShowLedValueyvalue,Yaxis break case 2 ShowLedValuezvalue,Zaxis breakCopyright Copyright 2001 by ICP DAS. All right are reserved Trademark I-8091 2-axis stepping/servo motor control card User ManualVersion 1.0 06/2001 Edition Features I-8091 2-axis Stepping/Servo Motor Control CardI-8091 Contents 1. Introduction 1.1 System Block Diagram1.2 DDA Technology Example Stepping Motor Example Pulse type input Servo Motor I-8000, 4 slots I-8000, 8 slots 2 Hardware2.1 I-8000 hardware address 2.2 Registers of I-8091 board 2.3 LED Indicator Y axis 2.4 Hardware Configuration 2.4.1 Limit switch configuration2.4.3 Direction configuration 2.4.2 Output pulse mode configuration2.4.4 Turn Servo ON/OFF Hold ON/OFF 2.4.5 Automatic protection2.4.6 Set limit switch as normal close condition 2.5 Connection 2.5.1 Pin assignment of connector CN22.5.3 The internal circuit of limit switch input I-8091 User Manual 2.5.4 Example of connectionVersion 1.0 06/2001 2-16Version 1.0 06/2001 I-8091 User ManualS8090 card 2-17Constants 3. Software3.1 Functions Version 1.0 06/2001 I-8091 User Manual2-19 ICPDAS2 i8091RESETSYSTEM unsigned char cardNo 3.1.1 Setting commandsunsigned int LowSpeedLow Speed ≤ DDA cycle≤High Speed≤ LowSpeed = AccDecunsigned char modeY 5 i8091SETMODEunsigned char cardNo, unsigned char modeX6 i8091SETSERVOONunsigned char cardNo unsigned char sonX, unsigned char sonYnormal open default Limit switches ORG1, LS11, LS14, ORG2, LS21, LS24, EMGcardNo card number 0~19 sw 0NO11 i8091EMGSTOPunsigned char cardNo 3.1.2 Stop Commands12 i8091LSPORGunsigned char cardNo 3.1.3 Simple motion commandsunsigned char DIR, unsigned char AXIS 14 i8091LSPPULSEMOVEunsigned char cardNo16 i8091LSPMOVEunsigned char cardNo 15 i8091HSPPULSEMOVEunsigned char cardNounsigned char AXIS, long pulseN unsigned char DIR, unsigned char AXISunsigned char DIR, unsigned char AXIS 17 i8091HSPMOVEunsigned char cardNoLow speed high speedcommand i8091STOPX, i8091STOPY, i8091STOPALL, or i8091SLOWSTOP Version 1.0 06/2001 I-8091 User Manual2-29 ICPDAS− 2047≤ # Xpulse≤ − 2047≤ #Ypulse≤ 3.1.4 Interpolation commandsunsigned int speed unsigned char accmode #Ypulse≤23 i8091INTPLINE02unsigned char cardNo, long x, long y Y X,Y CW X CCW where r adius = sqr tX2 + Y2 #≤ y 2− #≤ x 2−#≤ R 2− R ≥i8091INTPLINE02, i8091INTPCIRCLE02 and 26 unsigned char i8091INTPSTOP3.1.5 Others Page end of program i8091RESETSYSTEMCARD1 i8091RESETSYSTEMCARD13.2 Start up and end of program Start up programICPDAS Version 1.0 06/20012-38 4.1 Detect I-8091 card 4. Example4.3 ExampleDEMO1.cpp 4.2 Example DEMO.cppVersion 1.0 06/2001 2-40