Manuals / Integra / Home Audio / Stereo Receiver

Integra DTR-5.8 instruction manual First Time Setup—Continued, Next, Retry, Cancel, Notes

Models: DTR-5.8

1 100

Download 100 pages 21.79 Kb

Page 42

First Time Setup—Continued

First Time Setup—Continued

2

3

Put the speaker setup micro- phone at measurement point

(page 41), and connect it to the Setup Mic jack.

Auto Speaker Setup

AUDYSSEY

Please place microphone at center

of listening area at ear height.

Push Enter : Next

Notes:

•Make sure the microphone is hori- zontal.

•If there’s an obstacle between the microphone and any speaker, the automatic setup will not work cor- rectly. Set up the room as you would when enjoying a DVD.

•Positioning the microphone close to where your ears would normally be will provide better results. You can adjust the height of the microphone by using a tripod or level table.

Press [Enter].

The automatic speaker setup starts.

Auto Speaker Setup

AUDYSSEY

Do not unplug microphone.

Please keep quiet.

Now Measuring. . .

A test tone is output by each speaker in turn, as the Audyssey 2EQ function determines which speakers are con- nected. This takes a few minutes.

Note:

If any extraneous noise is picked up by the microphone, the automatic setup may not work correctly, so don’t make any noise.

4

5

The speaker detect results appear.

	Auto Speaker Setup
	Auto Speaker Setup			AUDYSSEY

- - - - - SP Detect Result - - - - -
FL	: Yes	FR	: Yes
SL	: Yes	SR	: Yes
SBL	: Yes	SBR	: Yes
C	: No	SW	: Yes

Next
Retry
Cancel

“Yes” means that the speaker was detected. “No” means that no speaker was detected.

If you agree with the results, use the Up and Down []/[ ] but- tons to select Next, and then press [Enter].

The options are:

Next:

Proceed to the next step.

Retry:

Return to step 2 and try again.

Cancel:

Cancel the automatic speaker setup.

The following screen appears.

Auto Speaker Setup

AUDYSSEY

Please place microphone at right end

of listening area at ear height.

Push Enter : Next

Move the speaker setup micro- phone to measurement point

(page 41), then press [Enter].

Audyssey 2EQ performs more mea- surements. This takes a few minutes.

42

Image 42

Integra DTR-5.8 instruction manual First Time Setup—Continued, Next, Retry, Cancel, Notes

Contents

DTR-5.8 AV ReceiverInstruction Manual Important Safety Instructions AVIS6.Handling Notes Precautions4.Power FCC Information for UserSupplied Accessories Introduction Table of ContentsFirst Time Setup ConnectionsProcessing FeaturesAmplification Connections5 6 7 8 9 bkbl bm bn bo bp Front & Rear Panels1 2 3 bq br bsFront & Rear Panels—Continued Tuning indicators Display SLEEP indicator MUTING indicatorRear Panel 56 7 8 9 bk blbmbn bo bpbq br bs bt ckclcm cn co Front & Rear Panels—ContinuedFront & Rear Panels—Continued 6 AC INLETAiming the Remote Controller Remote ControllerInstalling the Batteries Notes1 2 3 4bl 1 5bm Remote Controller—ContinuedUsing the Remote Controller Receiver/Tape ModeRemote Controller—Continued Zone 2 button1 2 bl 3 4bm 5 6bn 7 8bo 9bp DVD ModeRemote Controller—Continued To select the input source, press 1 2 8 3 49 5bk 6 bl bmCD/MD/CDR/Dock Mode Remote Controller—ContinuedFront left and right speakers About Home TheaterEnjoying Home Theater Center speakerOptical Digital Jacks Connecting the AV receiverAbout AV Connections AV Connection Color CodingSpeaker Configuration Connecting the AV receiver—ContinuedConnecting Your Speakers Using Dipole SpeakersConnecting the AV receiver—Continued Speaker Connection PrecautionsConnecting the Speaker Cables wires tightly, as shownBi-ampingthe Front Speakers Bi-ampingSpeaker HookupConnecting the AV receiver—Continued Connecting the AM Loop Antenna Connecting AntennaConnecting the Indoor FM Antenna Connecting the AV receiver—ContinuedConnecting the AV receiver-Continued Connecting an Outdoor FM AntennaConnecting an Outdoor AM Antenna Using a TV/FM Antenna SplitterVideo Connection Formats Connecting Both Audio & VideoWhich Connections Should I Use? Connecting the AV receiver—ContinuedAudio Connection Formats Connecting the AV receiver—ContinuedHDMI Monitor Setting Set to No Hint Connecting Your TV or Projectorb C c Connecting the AV receiver—ContinuedConnecting a DVD Player Connecting the AV receiver-Continued7.1 ch Hooking Up the Multichannel DVD InputConnecting the AV receiver—Continued 5.1 chConnecting a VCR or DVD Recorder for Playback Connecting the AV receiver—ContinuedHint Connecting a VCR or DVD Recorder for Recording Connecting the AV receiver—ContinuedConnecting the AV receiver—Continued HintSatellite, cable, set-topbox, etc Connecting a Game Console Connecting the AV receiver—ContinuedGame Console Connecting a Camcorder or Other Device Connecting the AV receiver-ContinuedCamcorder, etc Supported Audio Formats Connecting Components with HDMIAbout HDMI About Copyright ProtectionVideo Signals Making HDMI ConnectionsConnecting the AV receiver—Continued Audio SignalsStep Connecting a CD Player or TurntableConnecting the AV receiver—Continued Turntable MM with no Phono Preamp Built-inRI Dock with video Connecting an RI DockConnecting the AV receiver—Continued RI Dock without videoConnecting a Power Amplifier Connecting the AV receiver—ContinuedConnecting the Power Cord Connecting ComponentsConnecting the RS232 Port Connecting the AV receiver—ContinuedSmooth Operation in a Few Easy Steps Turning On the AV ReceiverTurning On and Standby Connecting the Power CordUsing Audyssey 2EQ First Time SetupAutomatic Speaker Setup Audyssey 2EQ 2, 3-8Next First Time Setup—ContinuedCancel RetryReview SP Level Review SP ConfigReview SP Distance First Time Setup—ContinuedSpeaker Detect Errors Error MessagesFirst Time Setup—Continued Write ErrorReviewing the Results Changing the Speaker Settings ManuallyUsing a Powered Subwoofer First Time Setup—ContinuedSubmenus About the Onscreen Setup MenusFirst Time Setup-Continued Main menuThe Input/Output Assign menu 1 2, 2-4HDMI Monitor appearsThe HDMI Input menu appears Video Input SetupHDMI Input Setup First Time Setup—Continuedappears Component Video SetupFirst Time Setup—Continued NotesExamples Digital Input SetupThe Digital Input menu appears First Time Setup—ContinuedChanging the Input Display Speaker SettingsThe Speaker Settings menu appears First Time Setup—ContinuedTV Format Setup not North American model The OSD Setup menu appearsFirst Time Setup-Continued AM Frequency Step Setup Australian model 1 2 3First Time Setup—Continued Basic Operations 1 3 1Selecting the Input Source Basic Operations—Continued Using the Multichannel DVD InputAdjusting the Bass & Treble Displaying Source InformationUsing Headphones Setting the Display BrightnessUsing the Sleep Timer Muting the AV receiverTuning into weak FM stereo stations Using the TunerTuning into Radio Stations Listening to the RadioDeleting Presets Presetting AM/FM StationsSelecting Presets Listening to the Radio—ContinuedSelecting Listening Modes Using the Listening ModesSelecting with the Remote Controller Selecting on the AV receiverUsing the Listening Modes—Continued Listening Modes Available for Each Source FormatAnalog and PCM Sources Using the Listening Modes—Continued Dolby DDTS and DTS 96/24 Sources Using the Listening Modes—ContinuedUsing the Listening Modes—Continued DTS-HDMaster Audio*1About the Listening Modes Using the Listening Modes—ContinuedOnkyo Original DSP Modes Using the Listening Modes—ContinuedRecording Separate AV Sources RecordingAV Recording NotesAdvanced Operations Using the CinemaFILTERAdjusting Individual Speaker Levels Dolby Digital, Dolby Digital PlusSpeaker Settings Advanced SetupSpeaker Setup 1 2 3 4 56 7 8 9 Advanced Setup-ContinuedThe setup menu closes Low-PassFilter for the LFE ChannelThe Speaker Distance menu appears 1 2, 2-6 1,Speaker Distance Advanced Setup—ContinuedThe Level Calibration menu appears 1 2, 2-5 1,Speaker Level Calibration the front left speaker2, 2-7 Equalizer SettingThe Speaker Setup menu appears Advanced Setup-ContinuedThe Analog Multich menu appears Multichannel DVD Input SettingsSubwoofer Input Sensitivity Advanced Setup—ContinuedInput Channel Settings Audio Adjust FunctionsTone Control Settings The settings are explained belowT-D Theater-DimensionalListening Setting PLIIx/Neo:6 Music Mode SettingsDolby EX Input Signal Setting Advanced Setup—ContinuedAssigning Listening Modes to Input SourcesAdvanced Setup-Continued 2 3 4 5 6 Source SetupIntelliVolume 1 3 2, 2, 4, 1,Advanced Setup—Continued 2 3 4Correcting Sound and Picture Sync lowed by the Setup buttonThe Volume Setup menu appears Volume Setup/OSD SetupVolume Setup Advanced Setup—ContinuedAdvanced Setup—Continued OSD Setup4 : 16 : The OSD Setup menu appearsChanging the AV receiver’s ID HDMI SetupThe Remote Control menu appears The HDMI menu appearsxvYCC HDMI Audio OutLip Sync ControlChanging the Remote Controller’s ID Lock SetupDigital Input Signal Formats Advanced Setup—ContinuedUsing Another Amp in Zone Connecting ZoneSetting the Powered Zone Using Only Speakers in ZoneThe Zone2 menu appears Setting the Zone 2 OutZone 2—Continued The Zone2 menu appearsControlling Zone 2 from the AV receiver Using ZoneControlling Zone 2 with the Remote Controller TRIGGER OUT goes high +12To Mute Zone Adjusting the Volume for ZoneAdjusting the Tone and Balance for Zone Zone 2—ContinuedThe main menu appears onscreen Zone 2—ContinuedHookup Using a Multiroom Kit with Other Components Using a Multiroom Kit with a CabinetUsing a Multiroom Kit with Zone Zone 2—ContinuedEntering Remote Control Codes Controlling Other ComponentsNotes Resetting Remote Mode Buttons Resetting the Remote ControllerControlling Other Components—Continued Controlling a TV Video Section SpecificationsAmplifier Section Tuner SectionTroubleshooting PowerAudio Troubleshooting—Continued VideoTroubleshooting—Continued Remote ControllerTuner The remote controller doesn’t workZone Video ATT 0 defaultRecording OthersMEMO MEMO Integra Division of ONKYO CORPORATION 2 9 3 4 4 5Integra Division of ONKYO U.S.A. CORPORATION Tel: 072-831-8023Fax: