Manuals / Intel / Computer Equipment / Computer Hardware

Intel CB60-BX, CB60-ZX manual Hardware Installation 2.7.10 AGP Fan Connector, SB-LINKConnector

Models: CB60-ZX CB60-BX

1 62

Download 62 pages 57.2 Kb

Page 22

Image 22

Hardware Installation

2.7.10 AGP Fan Connector

The system board is equipped with an AGP fan connector. If the system board is installed with an AGP add-in card and you wish to install a fan on the add-in card, connect the fan’s connector to location J11 on the system board. Refer to the add-in card’s manual for instructions on installing the fan.

Pin	Function

1	Ground

2+12V

N. C.

2.7.11 SB-LINK™ Connector

If the system board is installed with a Creative sound card that requires connecting the card to the SB-LINK™ connector, connect the cable that came with the sound card to connector J13. Refer to the sound card’s manual for more information.

Pin	Function

1	PC-PCI-GNTx
2	DGND
3	Key

4	PC-PCI-REQx

5	DGND

6	SERIRQ

Page 22

Image 22

Intel CB60-BX, CB60-ZX manual Hardware Installation 2.7.10 AGP Fan Connector, SB-LINKConnector

Contents

37400849 CB60-BX/ZXCopyright TrademarksFCC and DOC Statement on Class B Chapter 3 - Award BIOS Setup Utility Table of ContentsChapter 2 - Hardware Installation Chapter 1 - IntroductionAppendix A - System Error Messages Appendix B - TroubleshootingChapter 1 - Introduction 1.1 Features and Specifications1.1.1 Features ChipsetExpansion Slots ConnectorsIntroduction Desktop Management Interface DMIPCI Bus Master IDE Controller BIOS1.1.2System Health Monitor Functions IrDA InterfaceRTC Timer to Power-onthe System Dual Function Power ButtonThis feature supports external modem only Introduction 1.1.3 IntelligenceVirus Protection 1.2 Package ChecklistACPI IntroductionChapter 2 - Hardware Installation 2.1 System Board LayoutHardware Installation CB60-ZXIn the example above Switch 1 Off Switch 2 On 2.2 System MemoryHardware Installation Switch 3 Off Switch 4 OnHardware Installation 2.4 Jumper Settings for the CPU’s Front Side BusJumper JP2 CPU’s Front Side Bus Select Jumper JP2’s settings are shown below 2.5 Jumper Settings for Clearing CMOS DataHardware Installation Jumper JP3 Clear CMOS DataHardware Installation Warning 1. If JP1 was previously enabledwith a password set in the 1-2On Disable2.7.2 PS/2 Mouse and Keyboard Ports 2.7.1 Serial PortsHardware Installation Hardware Installation 2.7.3 Parallel Ports 2.7.4 Floppy Disk ControllerAdding a Second IDE Hard Drive 2.7.5 IDE Hard Disk InterfaceHardware Installation Hardware Installation 2.7.6 USB Ports 2.7.7 IrDA ConnectorHardware Installation 2.7.8 CPU Fan Connector 2.7.9 Chassis Fan ConnectorHardware Installation 2.7.10 AGP Fan Connector 2.7.11 SB-LINKConnector1+5VSB 720mA Hardware Installation 2.7.12 Wake-On-LANConnectorGround Hardware Installation 2.7.13 Power Connector G-SW Green Switch 2.7.14 J14 LEDs and SwitchesATX-SW ATX Power Switch RESET Reset SwitchKEYLOCK Power/Standby LED and Keylock Connector Hardware Installation3.1.1 Standard CMOS Setup Chapter 3 - Award BIOS Setup Utility3.1 The Basic Input/Output System Date Award BIOS Setup UtilityTime Halt On Drive A and Drive BVideo Award BIOS Setup UtilityVirus Warning 3.1.2 BIOS Features SetupAward BIOS Setup Utility Boot Up Floppy Seek Quick Power On Self TestBoot Sequence CPU L1 Cache and CPU L2 CacheTypematic Delay Msec Boot Up NumLock StatusTypematic Rate Setting Typematic Rate Chars/SecHDD S.M.A.R.T. Capability 3.1.3 Chipset Features SetupOS Select for DRAM 64MB Award BIOS Setup UtilityVideo BIOS Cacheable SDRAM RAS-to-CASDelaySystem BIOS Cacheable SDRAM RAS Precharge TimePCI 2.1 Compliance Video RAM CacheableMemory Hole At 15M-16M AGP Aperture Size MBSystem Health Monitor Spread SpectrumAward BIOS Setup Utility +1.5V, +3.3V, +5V, +12V, -12Vand 3.1.4Power Management SetupCPUV Award BIOS Setup UtilityPM Control by APM Power ManagementACPI Function Video Off MethodMODEM Use IRQ HDD Power DownVideo Off After Standby ModeResume On Ring Soft-Offby PWR-BTTNPWR Lost Resume State Award BIOS Setup UtilityResume On LAN Resume On AlarmTimer hh mm ss Date of MonthResources Controlled By 3.1.5 PNP/PCI ConfigurationReset Configuration Data Award BIOS Setup UtilityAssign IRQ for USB 3.1.6 Load Fail-SafeSettingsAssign IRQ for VGA PCI Slot 1 Use IRQ to PCI Slot 4 Use IRQIDE HDD Block Mode 3.1.7 Load Optimal Settings3.1.8 Integrated Peripherals Award BIOS Setup UtilityInit Display First UDMAUSB Keyboard Support KBC Input ClockOnboard Serial Port 1 and Onboard Serial Port IR Transmission DelayOnboard FDC Controller UART2 Mode SelectAward BIOS Setup Utility Keyboard/Mouse Power OnDisabled Default setting 3.1.9 Supervisor Password Award BIOS Setup UtilityAward BIOS Setup Utility 3.1.10 User Password 3.1.11 IDE HDD Auto DetectionAward BIOS Setup Utility 3.1.12 Save & Exit Setup 3.1.13 Exit Without Saving4.1 Desktop Management Interface DMI Chapter 4 - Supported Softwares4.1.1 Running the DMI Utility Supported Softwares 4.1.2 Using the DMI Utility Edit DMILoad DMI File Supported Softwares Add DMISave DMI File 4.2 Hardware Doctor Utility Supported SoftwaresBeep EnableFaults Count 1 or Supported SoftwaresPolling Interval Temperature Unit4.3 Patch Utility for Windows Supported SoftwaresCMOS BATTERY HAS FAILED Appendix A - System Error MessageA.2 Error Messages CMOS CHECKSUM ERRORBIOS ROM checksum error - System halted System Error MessageKeyboard error or no keyboard present FLOPPY DISKS failB.1 Troubleshooting Checklist Appendix B -TroubleshootingMonitor/Display When the computer is turned on, nothing happens TroubleshootingPower Supply The computer cannot access the floppy driveHard disk failure Troubleshooting Hard DriveParallel Port Excessively long formatting periodKeyboard Troubleshooting Serial PortSystem Board