System Health Monitor Functions, IrDA Interface | Intel CB60-BX

1

Introduction

PCI Bus Master IDE Controller

•Two PCI IDE interfaces support up to four IDE devices

•Ultra DMA/33 supported (Synchronous Ultra DMA mode - data transfer rate up to a maximum of 33MB/sec.)

•PIO Mode 3 and Mode 4 Enhanced IDE (data transfer rate up to 16.6MB/sec.)

•Bus mastering reduces CPU utilization during disk transfer

•ATAPI CD-ROM, LS-120 and ZIP supported

IrDA Interface

The system board is equipped with an IrDA connector for wireless connectivity between your computer and peripheral devices. It supports peripheral devices that meet the IrDA or ASK IR standard.

USB Ports

The system board is equipped with two USB ports. USB allows data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.

BIOS

•Award BIOS, Windows® 95 Plug and Play compatible

•Flash EPROM for easy BIOS upgrades

1.1.2System Health Monitor Functions

The system board is capable of monitoring the following “system health” conditions.

•Monitors processor/system temperature and processor overheat alarm

•Monitors 1.5V/3.3V/±5V/±12V/VCORE voltages and failure alarm

•Monitors processor/chassis fan speed and failure alarm

•Automatic processor/chassis fan control

•Read back capability that displays accurate temperature, voltage and fan speed

8

Image 8

Intel CB60-BX, CB60-ZX manual System Health Monitor Functions, PCI Bus Master IDE Controller, IrDA Interface, USB Ports

Contents

CB60-BX/ZX 37400849 Copyright Trademarks FCC and DOC Statement on Class B Table of Contents Appendix a System Error Messages Appendix B Troubleshooting Introduction Features and SpecificationsFeatures Connectors IntroductionExpansion Slots Desktop Management Interface DMI System Health Monitor Functions PCI Bus Master IDE ControllerIrDA Interface USB Ports Introduction Intelligence Package Checklist Virus Protection Hardware Installation System Board Layout Hardware Installation DIP Switch Settings for Processors For Factory Use Only System Memory Jumper Settings for the CPU’s Front Side Bus Jumper JP2 CPU’s Front Side Bus Select Jumper Settings for Clearing Cmos Data Jumper JP3 Clear Cmos Data Jumper Settings for Wake-On-Keyboard/ Wake-On-Mouse Jumper JP1 Wake-On-Keyboard/Wake-On-Mouse Serial Ports 2 PS/2 Mouse and Keyboard Ports Hardware Installation Parallel Ports Floppy Disk Controller Hardware Installation IDE Hard Disk Interface Adding a Second IDE Hard Drive Hardware Installation USB Ports IrDA Connector Hardware Installation CPU Fan Connector Chassis Fan Connector Hardware Installation AGP Fan Connector SB-LINK Connector Hardware Installation Wake-On-LAN Connector Hardware Installation Power Connector COM PW-OK 5VSB Hardware Installation 14 J14 LEDs and Switches Keylock Power/Standby LED and Keylock Connector Keylock Basic Input/Output System Award Bios Setup UtilityStandard Cmos Setup Time Award Bios Setup UtilityDate Halt On Drive a and Drive BVideo Award Bios Setup Utility Bios Features Setup Virus Warning Quick Power On Self Test Boot SequenceBoot Up Floppy Seek CPU L1 Cache and CPU L2 Cache Boot Up NumLock Status Typematic Rate SettingTypematic Delay Msec Typematic Rate Chars/Sec HDD S.M.A.R.T. Capability Chipset Features SetupOS Select for Dram 64MB Sdram RAS-to-CAS Delay Dram Data Integrity Mode CB60-BX onlySystem Bios Cacheable Video Bios Cacheable Bit I/O Recovery Time and 16 Bit I/O Recovery Time Video RAM CacheableMemory Hole At 15M-16M PCI 2.1 Compliance Spread Spectrum System Health Monitor +1.5V, +3.3V, +5V, +12V, -12V Power Management SetupCpuv Power Management Acpi FunctionPM Control by APM Video Off Method Standby Mode Suspend ModeHDD Power Down Video Off After Resume On Ring Soft-Off by PWR-BTTNPWR Lost Resume State Resume On Alarm Timer hhmmssResume On LAN Date of Month Resources Controlled By Award Bios Setup Utility 5 PNP/PCI ConfigurationReset Configuration Data Load Fail-Safe Settings Assign IRQ for VGAAssign IRQ for USB PCI Slot 1 Use IRQ to PCI Slot 4 Use IRQ Integrated Peripherals Award Bios Setup Utility Load Optimal SettingsIDE HDD Block Mode On-Chip Primary PCI IDE and On-Chip Secondary PCI IDE USB Keyboard SupportInit Display First KBC Input Clock UART2 Mode Select IR Transmission DelayOnboard FDC Controller Onboard Serial Port 1 and Onboard Serial Port Parallel Port Mode, ECP Mode Use DMA and EPP Mode Select Keyboard/Mouse Power On Supervisor Password Award Bios Setup Utility User Password IDE HDD Auto Detection Award Bios Setup Utility Save & Exit Setup Exit Without Saving Running the DMI Utility Supported SoftwaresDesktop Management Interface DMI Supported Softwares Using the DMI Utility Edit DMI Save DMI File Supported Softwares Add DMILoad DMI File Hardware Doctor Utility Supported Softwares Beep EnableFaults Count 1 or Polling Interval Temperature UnitPatch Utility for Windows Post Beep Appendix a System Error MessageError Messages System Error Message Monitor/Display Appendix B -TroubleshootingTroubleshooting Checklist Floppy Drive TroubleshootingPower Supply Troubleshooting Hard Drive Parallel Port System Board Troubleshooting Serial PortKeyboard