Manuals / Intelligent Motion Systems / Computer Equipment / Computer Hardware

Intelligent Motion Systems UDAS-1001E user manual UDAS Drivers, Power Test, Troubleshooting Errors

Models: UDAS-1001E

1 65

Download 65 pages 26.36 Kb

Page 38

UDAS Drivers

Checking the System

UDAS Drivers

Verify the UDAS system driver is properly installed by following the instructions for the USB Port (above).

Click on the plus sign (+) located next to the Universal serial bus controller. When the directory opens, double-click III Taos USB Data Acquisition System. A pop-up window appears displaying a message that reads, This device is working properly.

If the III Taos USB Data Acquisition System icon does not appear in the USB devices list, verify that both of the LEDs located on the front panel of the UDAS unit are illuminated. Verify that your external equipment is not consuming excessive power. Refer to the power test in the next section.

Power Test

For proper operation, the power test requires:

•the UDAS device be powered.

•the UDAS device be connected to the USB.

•the UDAS device pass its power on self-test (POST).

•the UDAS device be initialized by the host computer.

To perform the power test:

1.Unplug the USB cable from the UDAS port.

2.Plug the USB unit cable back into the UDAS port.

•One LED illuminates immediately, indicating power.

•The computer monitor may display the Busy hourglass icon while the UDAS unit initializes.

•The UDAS status LED illuminates after POST and host enumeration.

3.Verify the UDAS unit has two LEDs illuminated.

Troubleshooting Errors

If the two LEDs do not illuminate:

•Disconnect the I/O signals from the unit.

•Unplug the unit for several seconds then reconnect the unit to see if the LEDs illuminate. Some built-in tests may fail if the board was incompletely reset, even for components that are functioning normally.

•Verify the unit is receiving power and the power LED is illuminated.

3-14

Image 38

Intelligent Motion Systems UDAS-1001E user manual UDAS Drivers, Power Test, Troubleshooting Errors

Contents

Multifunction Data Acquisition System UDAS-1001E Series Hardware User ManualINNOVATIVE PC Data Acquisition Solutions for theWarranty and Repair Policy Statement GeneralOnline Support Technical Assistance and ServiceStatic Sensitivity Email SupportFCC Radio Frequency Interference Statement TrademarksUse of Equipment Version UDAS-1001E Series User ManualRevision History DateChecking the System Configuration and InstallationUDAS-1001E Series Data Acquisition Systems Table of ContentsAppendix C Analog Input and Output Calibration Procedures SpecificationsAccessories Appendix A1.1 Introduction UDAS-1001E Series Data Acquisition SystemsChapter UDAS-1001E-11.1.1 Features SoftwareSupport LibraryUDAS SYSCHECK Analog InputAnalog Output U-Link Software Libraries for WindowsDigital Input/Output 1.2 UDAS 1001E Series Functional Description1.2.1 Data Acquisition Functions CounterStarting Conversions High-Speed Analog Input ModeStarting and Stopping the High-Speed Analog Input Mode Stopping Conversions Rate GeneratorChannel Scanner channel 7 channel High-Speed Analog Input Triggeringchannel 5 channel 6 channel 7 channel 0 channel Example Auto ZeroDigital I/O Analog OutputTermination CountersDigital I/O signals are TTL-compatible and perform functions such as reading digital inputs, driving digital outputs, and detecting input change-of-state 5.750 6.600 FIGURE 1.2 UDAS-1001E-4 dimensional drawing1.520 7.290Diagnostic 1.3 Software Support and Accessories1.2.2 Power 1.3.1 Software SupportVisual Designer UDAS Support Library LabVIEW UDAS Support Library2.1 Introduction Configuration and Installation2.2 Power-on Default Digital I/O Configuration Removing the CoverSetting the Configuration FIGURE 2.1 UDAS Switch S1Reinstalling the Cover Enabling the CJCJP2 Jumper Position DifferentialJP1 Jumper Position TABLE 2.1 CJC Jumper Positions2.3 Connecting the UDAS Unit Making the Initial ConnectionChapter 3 Checking the System 3.1 IntroductionUse your CD drive letter\Syscheck\SETUP.EXEENTER 3.2 Installing and Running UDAS SYSCHECKInstalling SYSCHECK 3.3 SYSCHECK Operation3.3.1 Unit Info FIGURE 3.1 Unit Info dialog3.3.2 System Check FIGURE 3.2 UDAS SYSCHECK System Check dialog3.3.2.1 Analog Input Test FIGURE 3.3 UDAS SYSCHECK Analog Input Test of a UDAS unit3.3.2.2 Analog Output Test FIGURE 3.4 UDAS SYSCHECK Analog Output Test of a UDAS unit3.3.2.3 Counter Test FIGURE 3.5 UDAS SYSCHECK Counter Test in Count ModeThe status field is looking for TTL transitions FIGURE 3.7 UDAS SYSCHECK Counter Test Measure Frequency Mode Digital I/O Test 3.3.3 Paced Analog Input FIGURE 3.10 High-Speed Aquisition Sample 3.4.1.1 Verify Lower Level Drivers 3.4 Troubleshooting Tips3.4.1 Basic Troubleshooting USB PortUDAS Drivers Power TestTroubleshooting Errors Check the wiring and cables for shorts or damage SPECIFICATION SpecificationsA.1 UDAS-1001E Series Hardware Specifications TABLE A.1 Hardware SpecificationsSpecifications TABLE A.1 Hardware Specifications ContinuedSPECIFICATION PARAMETERPARAMETER SPECIFICATIONTABLE A.1 Hardware Specifications Continued CONDITIONSFIGURE A.2 Dimensions of the UDAS unit Rear panel A.2 UDAS-1001E-3, UDAS-1001E-4 DimensionsFIGURE A.1 Dimensions of the UDAS unit Top view 1.295 FIGURE A.3 Dimensions of the UDAS unit Bottom view4.700 525 4.7005.305 FIGURE A.4 Dimensional Drawing of the UDAS series PCBMAXIMUM COMPONENT HEIGHT 4.70TABLE A.2 UDAS I/O Connectors A.3 UDAS I/O ConnectorsSignal Name Single Ended Input FunctionSingle Ended Input Function A.2 UDAS I/O Connectors ContinuedSignal Name Differential InputSingle Ended Input Function Signal NameA.2 UDAS I/O Connectors Continued Differential InputAppendix B AccessoriesTABLE B.1 Accessories for the UDAS-1001E Series B.1 UDAS Termination Panels B.1.1 PCI-20429T-1 Multifunction Termination PanelFIGURE B.2 PCI-20429T-1 Multifunction Termination Panel B.1.2 UDAS Termination and Signal Conditioning Options FIGURE B.3 UDAS-1001E Termination OptionsTo UDAS unit I/O ConnectorsFIGURE B.4 UDAS-1001E Termination Options continued Analog FIGURE B.5 Diagram of the PCI-20430A-1’s connectors and cablesAnalog In Single-Ended and Differential Function Analog In SinglePCI-1100 Series Digital Opto-Isolator Blocks Summary of FeaturesB.1.3 Isolator Blocks C.1.1 Removing the UDAS Unit’s Cover Appendix C Analog Input and Output Calibration ProceduresC.1 UDAS Analog Input Circuit Calibration Procedures Equipment RequiredTP21 R24 R25 R26 R36 Analog Input and Output Calibration ProceduresFIGURE C.1 Locations of Potentiometers for Adjusting Analog Circuits TP27Adjust Input Offset Voltage C.1.2 Analog Input Calibration ProcedureAdjust Offset and Gain for ±10Volt Input Range Adjust Offset and Gain for ± 5Volt Input Range Adjust Offset and Gain for 0 to 10 Volt Range C.2 UDAS Analog Output Circuit Calibration Procedure Equipment RequiredAnalog Output Channel 0 Offset and Gain Analog Output Channel 1 Offset and GainG gate F featuresIndex U UDAS