Manuals / Intelligent Motion Systems / Computer Equipment / Computer Hardware

Intelligent Motion Systems UDAS-1001E Parameter, Conditions, Specification, approximately

Models: UDAS-1001E

1 65

Page 42

PARAMETER	CONDITIONS	SPECIFICATION

Resolution		32-Bit

Number of Channels		1

Max Input frequency	TTL-level input	2 MHz


TimeBase Generator

Type	Crystal-based	Rate Generator (24-Bit)

Number		2 (1 analog input, 1 analog output)

Resolution		125 ns

Output Frequency Range		0.5 Hz to 1 Mhz

Output Levels		TTL-compatible


Bus Interface

Type		USB


Power

Voltage Range	USB or External	+5 V

Current Available (*1)	+5 V	200 mA maximum

Current Requirements	USB powered	<500 mA


Physical Characteristics

Size		5.75" D x 7.25" W x 1.60" H
		(approximately)
		14.61 cm D x 18.42 cm W x 4.06
		cm H

Operating Temperature		0 - 50 C
Range

All Specifications are typical at 25 C unless otherwise noted. Note (*1): When powered from an external source, the on-board power supply circuit can supply up to 200mA at 5VDC to termination panels through the 50-pin I/O connector.

TABLE A.1 Hardware Specifications (Continued)

A-3

Page 42

Image 42

Intelligent Motion Systems UDAS-1001E user manual Parameter, Conditions, TABLE A.1 Hardware Specifications Continued

Contents

Multifunction Data Acquisition System UDAS-1001E Series Hardware User ManualINNOVATIVE PC Data Acquisition Solutions for theWarranty and Repair Policy Statement GeneralOnline Support Technical Assistance and ServiceStatic Sensitivity Email SupportTrademarks Use of EquipmentFCC Radio Frequency Interference Statement Version UDAS-1001E Series User ManualRevision History DateChecking the System Configuration and InstallationUDAS-1001E Series Data Acquisition Systems Table of ContentsAppendix C Analog Input and Output Calibration Procedures SpecificationsAccessories Appendix A1.1 Introduction UDAS-1001E Series Data Acquisition SystemsChapter UDAS-1001E-11.1.1 Features SoftwareSupport LibraryUDAS SYSCHECK Analog InputAnalog Output U-Link Software Libraries for WindowsDigital Input/Output 1.2 UDAS 1001E Series Functional Description1.2.1 Data Acquisition Functions CounterHigh-Speed Analog Input Mode Starting and Stopping the High-Speed Analog Input ModeStarting Conversions Rate Generator Channel ScannerStopping Conversions High-Speed Analog Input Triggering channel 5 channel 6 channel 7 channel 0 channelchannel 7 channel Example Auto ZeroDigital I/O Analog OutputCounters Digital I/O signals are TTL-compatible and perform functions such as reading digital inputs, driving digital outputs, and detecting input change-of-stateTermination 5.750 6.600 FIGURE 1.2 UDAS-1001E-4 dimensional drawing1.520 7.290Diagnostic 1.3 Software Support and Accessories1.2.2 Power 1.3.1 Software SupportVisual Designer UDAS Support Library LabVIEW UDAS Support Library2.1 Introduction Configuration and Installation2.2 Power-on Default Digital I/O Configuration Removing the CoverSetting the Configuration FIGURE 2.1 UDAS Switch S1Reinstalling the Cover Enabling the CJCJP2 Jumper Position DifferentialJP1 Jumper Position TABLE 2.1 CJC Jumper Positions2.3 Connecting the UDAS Unit Making the Initial ConnectionChapter 3 Checking the System 3.1 IntroductionUse your CD drive letter\Syscheck\SETUP.EXEENTER 3.2 Installing and Running UDAS SYSCHECKInstalling SYSCHECK 3.3 SYSCHECK Operation3.3.1 Unit Info FIGURE 3.1 Unit Info dialog3.3.2 System Check FIGURE 3.2 UDAS SYSCHECK System Check dialog3.3.2.1 Analog Input Test FIGURE 3.3 UDAS SYSCHECK Analog Input Test of a UDAS unit3.3.2.2 Analog Output Test FIGURE 3.4 UDAS SYSCHECK Analog Output Test of a UDAS unit3.3.2.3 Counter Test FIGURE 3.5 UDAS SYSCHECK Counter Test in Count ModeThe status field is looking for TTL transitions FIGURE 3.7 UDAS SYSCHECK Counter Test Measure Frequency Mode Digital I/O Test 3.3.3 Paced Analog Input FIGURE 3.10 High-Speed Aquisition Sample 3.4.1.1 Verify Lower Level Drivers 3.4 Troubleshooting Tips3.4.1 Basic Troubleshooting USB PortPower Test Troubleshooting ErrorsUDAS Drivers Check the wiring and cables for shorts or damage SPECIFICATION SpecificationsA.1 UDAS-1001E Series Hardware Specifications TABLE A.1 Hardware SpecificationsSpecifications TABLE A.1 Hardware Specifications ContinuedSPECIFICATION PARAMETERPARAMETER SPECIFICATIONTABLE A.1 Hardware Specifications Continued CONDITIONSA.2 UDAS-1001E-3, UDAS-1001E-4 Dimensions FIGURE A.1 Dimensions of the UDAS unit Top viewFIGURE A.2 Dimensions of the UDAS unit Rear panel 1.295 FIGURE A.3 Dimensions of the UDAS unit Bottom view4.700 525 4.7005.305 FIGURE A.4 Dimensional Drawing of the UDAS series PCBMAXIMUM COMPONENT HEIGHT 4.70TABLE A.2 UDAS I/O Connectors A.3 UDAS I/O ConnectorsSignal Name Single Ended Input FunctionSingle Ended Input Function A.2 UDAS I/O Connectors ContinuedSignal Name Differential InputSingle Ended Input Function Signal NameA.2 UDAS I/O Connectors Continued Differential InputAccessories TABLE B.1 Accessories for the UDAS-1001E SeriesAppendix B B.1 UDAS Termination Panels B.1.1 PCI-20429T-1 Multifunction Termination PanelFIGURE B.2 PCI-20429T-1 Multifunction Termination Panel B.1.2 UDAS Termination and Signal Conditioning Options FIGURE B.3 UDAS-1001E Termination OptionsI/O Connectors FIGURE B.4 UDAS-1001E Termination Options continuedTo UDAS unit Analog FIGURE B.5 Diagram of the PCI-20430A-1’s connectors and cablesAnalog In Single-Ended and Differential Function Analog In SingleSummary of Features B.1.3 Isolator BlocksPCI-1100 Series Digital Opto-Isolator Blocks C.1.1 Removing the UDAS Unit’s Cover Appendix C Analog Input and Output Calibration ProceduresC.1 UDAS Analog Input Circuit Calibration Procedures Equipment RequiredTP21 R24 R25 R26 R36 Analog Input and Output Calibration ProceduresFIGURE C.1 Locations of Potentiometers for Adjusting Analog Circuits TP27C.1.2 Analog Input Calibration Procedure Adjust Offset and Gain for ±10Volt Input RangeAdjust Input Offset Voltage Adjust Offset and Gain for ± 5Volt Input Range Adjust Offset and Gain for 0 to 10 Volt Range C.2 UDAS Analog Output Circuit Calibration Procedure Equipment RequiredAnalog Output Channel 0 Offset and Gain Analog Output Channel 1 Offset and GainF features IndexG gate U UDAS

(approximately)