Manuals / Intelligent Motion Systems / Computer Equipment / Computer Hardware

Intelligent Motion Systems UDAS-1001E user manual Adjust Offset and Gain for 0 to 10 Volt Range

Models: UDAS-1001E

1 65

Download 65 pages 26.36 Kb

Page 60

Adjust Offset and Gain for 0 to 10 Volt Range

9.Repeat the procedure and verify the adjustments are correct.

Note: These adjustment steps are very interactive and may require several iterations.

Adjust Offset and Gain for 0 to 10 Volt Range

1.Verify the termination panel is attached to the 50-pin connector of a UDAS unit. Begin with step 2 if the unit has built-in termination.

2.Attach a voltage calibrator to channel 0 with all of the other channels grounded.

3.Run a program to configure the UDAS for a range of 0-10 V and a gain of 1.

4.Set the calibrated input to 0.02441 V.

5.Set SYSCHECK or other program to average 50 readings. Manually or automatically take readings repeatedly.

6.Adjust Pot R38 for 0.02441 V.

Note: On all adjustments there will be a range of adjustment that results in the proper reading. Determine this range and leave the adjustment in the center of the range.

7.Set the calibrated input to 9.97558 V.

8.Adjust Pot R45 for 9.7558 V.

9.Repeat steps 4 through 8. There will be a very slight interaction in these adjustments.

10.After calibrating the unit, slide the unit’s cover back on and refasten the front panel using the screws removed earlier.

C-5

Image 60

Intelligent Motion Systems UDAS-1001E user manual Adjust Offset and Gain for 0 to 10 Volt Range

Contents

UDAS-1001E Series Hardware User Manual INNOVATIVE PC Data Acquisition SolutionsMultifunction Data Acquisition System for theWarranty and Repair Policy Statement GeneralTechnical Assistance and Service Static SensitivityOnline Support Email SupportTrademarks Use of EquipmentFCC Radio Frequency Interference Statement UDAS-1001E Series User Manual Revision HistoryVersion DateConfiguration and Installation UDAS-1001E Series Data Acquisition SystemsChecking the System Table of ContentsSpecifications AccessoriesAppendix C Analog Input and Output Calibration Procedures Appendix AUDAS-1001E Series Data Acquisition Systems Chapter1.1 Introduction UDAS-1001E-11.1.1 Features SoftwareSupport LibraryAnalog Input Analog OutputUDAS SYSCHECK U-Link Software Libraries for Windows1.2 UDAS 1001E Series Functional Description 1.2.1 Data Acquisition FunctionsDigital Input/Output CounterHigh-Speed Analog Input Mode Starting and Stopping the High-Speed Analog Input ModeStarting Conversions Rate Generator Channel ScannerStopping Conversions High-Speed Analog Input Triggering channel 5 channel 6 channel 7 channel 0 channelchannel 7 channel Auto Zero Digital I/OExample Analog OutputCounters Digital I/O signals are TTL-compatible and perform functions such as reading digital inputs, driving digital outputs, and detecting input change-of-stateTermination FIGURE 1.2 UDAS-1001E-4 dimensional drawing 1.5205.750 6.600 7.2901.3 Software Support and Accessories 1.2.2 PowerDiagnostic 1.3.1 Software SupportVisual Designer UDAS Support Library LabVIEW UDAS Support LibraryConfiguration and Installation 2.2 Power-on Default Digital I/O Configuration2.1 Introduction Removing the CoverSetting the Configuration FIGURE 2.1 UDAS Switch S1Reinstalling the Cover Enabling the CJCDifferential JP1 Jumper PositionJP2 Jumper Position TABLE 2.1 CJC Jumper Positions2.3 Connecting the UDAS Unit Making the Initial ConnectionChapter 3 Checking the System 3.1 Introduction3.2 Installing and Running UDAS SYSCHECK Installing SYSCHECKUse your CD drive letter\Syscheck\SETUP.EXEENTER 3.3 SYSCHECK Operation3.3.1 Unit Info FIGURE 3.1 Unit Info dialog3.3.2 System Check FIGURE 3.2 UDAS SYSCHECK System Check dialog3.3.2.1 Analog Input Test FIGURE 3.3 UDAS SYSCHECK Analog Input Test of a UDAS unit3.3.2.2 Analog Output Test FIGURE 3.4 UDAS SYSCHECK Analog Output Test of a UDAS unit3.3.2.3 Counter Test FIGURE 3.5 UDAS SYSCHECK Counter Test in Count ModeThe status field is looking for TTL transitions FIGURE 3.7 UDAS SYSCHECK Counter Test Measure Frequency Mode Digital I/O Test 3.3.3 Paced Analog Input FIGURE 3.10 High-Speed Aquisition Sample 3.4 Troubleshooting Tips 3.4.1 Basic Troubleshooting3.4.1.1 Verify Lower Level Drivers USB PortPower Test Troubleshooting ErrorsUDAS Drivers Check the wiring and cables for shorts or damage Specifications A.1 UDAS-1001E Series Hardware SpecificationsSPECIFICATION TABLE A.1 Hardware SpecificationsTABLE A.1 Hardware Specifications Continued SPECIFICATIONSpecifications PARAMETERSPECIFICATION TABLE A.1 Hardware Specifications ContinuedPARAMETER CONDITIONSA.2 UDAS-1001E-3, UDAS-1001E-4 Dimensions FIGURE A.1 Dimensions of the UDAS unit Top viewFIGURE A.2 Dimensions of the UDAS unit Rear panel FIGURE A.3 Dimensions of the UDAS unit Bottom view 4.700 5251.295 4.700FIGURE A.4 Dimensional Drawing of the UDAS series PCB MAXIMUM COMPONENT HEIGHT5.305 4.70A.3 UDAS I/O Connectors Signal NameTABLE A.2 UDAS I/O Connectors Single Ended Input FunctionA.2 UDAS I/O Connectors Continued Signal NameSingle Ended Input Function Differential InputSignal Name A.2 UDAS I/O Connectors ContinuedSingle Ended Input Function Differential InputAccessories TABLE B.1 Accessories for the UDAS-1001E SeriesAppendix B B.1 UDAS Termination Panels B.1.1 PCI-20429T-1 Multifunction Termination PanelFIGURE B.2 PCI-20429T-1 Multifunction Termination Panel B.1.2 UDAS Termination and Signal Conditioning Options FIGURE B.3 UDAS-1001E Termination OptionsI/O Connectors FIGURE B.4 UDAS-1001E Termination Options continuedTo UDAS unit FIGURE B.5 Diagram of the PCI-20430A-1’s connectors and cables Analog In Single-Ended and Differential FunctionAnalog Analog In SingleSummary of Features B.1.3 Isolator BlocksPCI-1100 Series Digital Opto-Isolator Blocks Appendix C Analog Input and Output Calibration Procedures C.1 UDAS Analog Input Circuit Calibration ProceduresC.1.1 Removing the UDAS Unit’s Cover Equipment RequiredAnalog Input and Output Calibration Procedures FIGURE C.1 Locations of Potentiometers for Adjusting Analog CircuitsTP21 R24 R25 R26 R36 TP27C.1.2 Analog Input Calibration Procedure Adjust Offset and Gain for ±10Volt Input RangeAdjust Input Offset Voltage Adjust Offset and Gain for ± 5Volt Input Range Adjust Offset and Gain for 0 to 10 Volt Range C.2 UDAS Analog Output Circuit Calibration Procedure Equipment RequiredAnalog Output Channel 0 Offset and Gain Analog Output Channel 1 Offset and GainF features IndexG gate U UDAS