Manuals / Intelligent Motion Systems / Computer Equipment / Computer Hardware

Intelligent Motion Systems UDAS-1001E Analog Input and Output Calibration Procedures, TP27

Models: UDAS-1001E

1 65

Page 57

Analog Input and Output Calibration Procedures

4.Connect the UDAS to the host computer and allow at least a 15 minute warm-up period before performing the adjustments.

CAUTION:

The unit may become damaged if you use an uninsulated screwdriver and accidentally touch other components.

FIGURE C.1 Locations of Potentiometers for Adjusting Analog Circuits on page C-2 shows the locations of the potentiometers used to adjust the analog circuits on a UDAS unit.

0 0 0 0 0 0

TP21

R24

R25

R26

R36

R38

R39

R40

R46

R45

TP27

R58

FIGURE C.1 Locations of Potentiometers for Adjusting Analog Circuits

C-2

Page 57

Image 57

Intelligent Motion Systems UDAS-1001E Analog Input and Output Calibration Procedures, TP21 R24 R25 R26 R36, TP27

Contents

INNOVATIVE PC Data Acquisition Solutions UDAS-1001E Series Hardware User ManualMultifunction Data Acquisition System for theGeneral Warranty and Repair Policy StatementStatic Sensitivity Technical Assistance and ServiceOnline Support Email SupportTrademarks Use of EquipmentFCC Radio Frequency Interference Statement Revision History UDAS-1001E Series User ManualVersion DateUDAS-1001E Series Data Acquisition Systems Configuration and InstallationChecking the System Table of ContentsAccessories SpecificationsAppendix C Analog Input and Output Calibration Procedures Appendix AChapter UDAS-1001E Series Data Acquisition Systems1.1 Introduction UDAS-1001E-1SoftwareSupport Library 1.1.1 FeaturesAnalog Output Analog InputUDAS SYSCHECK U-Link Software Libraries for Windows1.2.1 Data Acquisition Functions 1.2 UDAS 1001E Series Functional DescriptionDigital Input/Output CounterHigh-Speed Analog Input Mode Starting and Stopping the High-Speed Analog Input ModeStarting Conversions Rate Generator Channel ScannerStopping Conversions High-Speed Analog Input Triggering channel 5 channel 6 channel 7 channel 0 channelchannel 7 channel Digital I/O Auto ZeroExample Analog OutputCounters Digital I/O signals are TTL-compatible and perform functions such as reading digital inputs, driving digital outputs, and detecting input change-of-stateTermination 1.520 FIGURE 1.2 UDAS-1001E-4 dimensional drawing5.750 6.600 7.2901.2.2 Power 1.3 Software Support and AccessoriesDiagnostic 1.3.1 Software SupportLabVIEW UDAS Support Library Visual Designer UDAS Support Library2.2 Power-on Default Digital I/O Configuration Configuration and Installation2.1 Introduction Removing the CoverFIGURE 2.1 UDAS Switch S1 Setting the ConfigurationEnabling the CJC Reinstalling the CoverJP1 Jumper Position DifferentialJP2 Jumper Position TABLE 2.1 CJC Jumper PositionsMaking the Initial Connection 2.3 Connecting the UDAS Unit3.1 Introduction Chapter 3 Checking the SystemInstalling SYSCHECK 3.2 Installing and Running UDAS SYSCHECKUse your CD drive letter\Syscheck\SETUP.EXEENTER 3.3 SYSCHECK OperationFIGURE 3.1 Unit Info dialog 3.3.1 Unit InfoFIGURE 3.2 UDAS SYSCHECK System Check dialog 3.3.2 System CheckFIGURE 3.3 UDAS SYSCHECK Analog Input Test of a UDAS unit 3.3.2.1 Analog Input TestFIGURE 3.4 UDAS SYSCHECK Analog Output Test of a UDAS unit 3.3.2.2 Analog Output TestFIGURE 3.5 UDAS SYSCHECK Counter Test in Count Mode 3.3.2.3 Counter TestThe status field is looking for TTL transitions FIGURE 3.7 UDAS SYSCHECK Counter Test Measure Frequency Mode Digital I/O Test 3.3.3 Paced Analog Input FIGURE 3.10 High-Speed Aquisition Sample 3.4.1 Basic Troubleshooting 3.4 Troubleshooting Tips3.4.1.1 Verify Lower Level Drivers USB PortPower Test Troubleshooting ErrorsUDAS Drivers Check the wiring and cables for shorts or damage A.1 UDAS-1001E Series Hardware Specifications SpecificationsSPECIFICATION TABLE A.1 Hardware SpecificationsSPECIFICATION TABLE A.1 Hardware Specifications ContinuedSpecifications PARAMETERTABLE A.1 Hardware Specifications Continued SPECIFICATIONPARAMETER CONDITIONSA.2 UDAS-1001E-3, UDAS-1001E-4 Dimensions FIGURE A.1 Dimensions of the UDAS unit Top viewFIGURE A.2 Dimensions of the UDAS unit Rear panel 4.700 525 FIGURE A.3 Dimensions of the UDAS unit Bottom view1.295 4.700MAXIMUM COMPONENT HEIGHT FIGURE A.4 Dimensional Drawing of the UDAS series PCB5.305 4.70Signal Name A.3 UDAS I/O ConnectorsTABLE A.2 UDAS I/O Connectors Single Ended Input FunctionSignal Name A.2 UDAS I/O Connectors ContinuedSingle Ended Input Function Differential InputA.2 UDAS I/O Connectors Continued Signal NameSingle Ended Input Function Differential InputAccessories TABLE B.1 Accessories for the UDAS-1001E SeriesAppendix B B.1.1 PCI-20429T-1 Multifunction Termination Panel B.1 UDAS Termination PanelsFIGURE B.2 PCI-20429T-1 Multifunction Termination Panel FIGURE B.3 UDAS-1001E Termination Options B.1.2 UDAS Termination and Signal Conditioning OptionsI/O Connectors FIGURE B.4 UDAS-1001E Termination Options continuedTo UDAS unit Analog In Single-Ended and Differential Function FIGURE B.5 Diagram of the PCI-20430A-1’s connectors and cablesAnalog Analog In SingleSummary of Features B.1.3 Isolator BlocksPCI-1100 Series Digital Opto-Isolator Blocks C.1 UDAS Analog Input Circuit Calibration Procedures Appendix C Analog Input and Output Calibration ProceduresC.1.1 Removing the UDAS Unit’s Cover Equipment RequiredFIGURE C.1 Locations of Potentiometers for Adjusting Analog Circuits Analog Input and Output Calibration ProceduresTP21 R24 R25 R26 R36 TP27C.1.2 Analog Input Calibration Procedure Adjust Offset and Gain for ±10Volt Input RangeAdjust Input Offset Voltage Adjust Offset and Gain for ± 5Volt Input Range Adjust Offset and Gain for 0 to 10 Volt Range Equipment Required C.2 UDAS Analog Output Circuit Calibration ProcedureAnalog Output Channel 1 Offset and Gain Analog Output Channel 0 Offset and GainF features IndexG gate U UDAS