Manuals / Intelligent Motion Systems / Computer Equipment / Computer Hardware

Intelligent Motion Systems UDAS-1001E TABLE A.1 Hardware Specifications Continued, Parameter

Models: UDAS-1001E

1 65

Page 41

Specifications

PARAMETER	CONDITIONS	SPECIFICATION

Noise	Input grounded at connector
	(RMS)

	Gain <=10	1.0 LSB

	Gain = 100	1.2

DC Accuracy		No missing codes, guaranteed

Linearity Error		±0.024%FS (± 1LSB)

Throughput		100 k Samples/second


Analog Trigger (with AO
option)

Range		±10 V

Hysterisis		28 mV

Resolution		4.88 mV nominal

Slope		Pos/Neg


Analog Outputs (Optional)

Number of Channels		2

Resolution		12 bits (1 part in 4096)

Voltage Ranges		±10 V

Throughput		100 k Samples/second


Digital I/O

Number of Ports	8 channels (bits) per port	2

Input Levels		TTL-compatible

Input Current	High Level / Low Level	23 μA/1 μA

Output Levels		TTL-compatible

Source/Sink	Vout = High/Low	15mA / 12mA

High-Speed Counter

TABLE A.1 Hardware Specifications (Continued)

A-2

Page 41

Image 41

Intelligent Motion Systems UDAS-1001E user manual TABLE A.1 Hardware Specifications Continued, Parameter, Conditions

Contents

INNOVATIVE PC Data Acquisition Solutions UDAS-1001E Series Hardware User ManualMultifunction Data Acquisition System for theGeneral Warranty and Repair Policy StatementStatic Sensitivity Technical Assistance and ServiceOnline Support Email SupportFCC Radio Frequency Interference Statement TrademarksUse of Equipment Revision History UDAS-1001E Series User ManualVersion DateUDAS-1001E Series Data Acquisition Systems Configuration and InstallationChecking the System Table of ContentsAccessories SpecificationsAppendix C Analog Input and Output Calibration Procedures Appendix AChapter UDAS-1001E Series Data Acquisition Systems1.1 Introduction UDAS-1001E-1SoftwareSupport Library 1.1.1 FeaturesAnalog Output Analog InputUDAS SYSCHECK U-Link Software Libraries for Windows1.2.1 Data Acquisition Functions 1.2 UDAS 1001E Series Functional DescriptionDigital Input/Output CounterStarting Conversions High-Speed Analog Input ModeStarting and Stopping the High-Speed Analog Input Mode Stopping Conversions Rate GeneratorChannel Scanner channel 7 channel High-Speed Analog Input Triggeringchannel 5 channel 6 channel 7 channel 0 channel Digital I/O Auto ZeroExample Analog OutputTermination CountersDigital I/O signals are TTL-compatible and perform functions such as reading digital inputs, driving digital outputs, and detecting input change-of-state 1.520 FIGURE 1.2 UDAS-1001E-4 dimensional drawing5.750 6.600 7.2901.2.2 Power 1.3 Software Support and AccessoriesDiagnostic 1.3.1 Software SupportLabVIEW UDAS Support Library Visual Designer UDAS Support Library2.2 Power-on Default Digital I/O Configuration Configuration and Installation2.1 Introduction Removing the CoverFIGURE 2.1 UDAS Switch S1 Setting the ConfigurationEnabling the CJC Reinstalling the CoverJP1 Jumper Position DifferentialJP2 Jumper Position TABLE 2.1 CJC Jumper PositionsMaking the Initial Connection 2.3 Connecting the UDAS Unit3.1 Introduction Chapter 3 Checking the SystemInstalling SYSCHECK 3.2 Installing and Running UDAS SYSCHECKUse your CD drive letter\Syscheck\SETUP.EXEENTER 3.3 SYSCHECK OperationFIGURE 3.1 Unit Info dialog 3.3.1 Unit InfoFIGURE 3.2 UDAS SYSCHECK System Check dialog 3.3.2 System CheckFIGURE 3.3 UDAS SYSCHECK Analog Input Test of a UDAS unit 3.3.2.1 Analog Input TestFIGURE 3.4 UDAS SYSCHECK Analog Output Test of a UDAS unit 3.3.2.2 Analog Output TestFIGURE 3.5 UDAS SYSCHECK Counter Test in Count Mode 3.3.2.3 Counter TestThe status field is looking for TTL transitions FIGURE 3.7 UDAS SYSCHECK Counter Test Measure Frequency Mode Digital I/O Test 3.3.3 Paced Analog Input FIGURE 3.10 High-Speed Aquisition Sample 3.4.1 Basic Troubleshooting 3.4 Troubleshooting Tips3.4.1.1 Verify Lower Level Drivers USB PortUDAS Drivers Power TestTroubleshooting Errors Check the wiring and cables for shorts or damage A.1 UDAS-1001E Series Hardware Specifications SpecificationsSPECIFICATION TABLE A.1 Hardware SpecificationsSPECIFICATION TABLE A.1 Hardware Specifications ContinuedSpecifications PARAMETERTABLE A.1 Hardware Specifications Continued SPECIFICATIONPARAMETER CONDITIONSFIGURE A.2 Dimensions of the UDAS unit Rear panel A.2 UDAS-1001E-3, UDAS-1001E-4 DimensionsFIGURE A.1 Dimensions of the UDAS unit Top view 4.700 525 FIGURE A.3 Dimensions of the UDAS unit Bottom view1.295 4.700MAXIMUM COMPONENT HEIGHT FIGURE A.4 Dimensional Drawing of the UDAS series PCB5.305 4.70Signal Name A.3 UDAS I/O ConnectorsTABLE A.2 UDAS I/O Connectors Single Ended Input FunctionSignal Name A.2 UDAS I/O Connectors ContinuedSingle Ended Input Function Differential InputA.2 UDAS I/O Connectors Continued Signal NameSingle Ended Input Function Differential InputAppendix B AccessoriesTABLE B.1 Accessories for the UDAS-1001E Series B.1.1 PCI-20429T-1 Multifunction Termination Panel B.1 UDAS Termination PanelsFIGURE B.2 PCI-20429T-1 Multifunction Termination Panel FIGURE B.3 UDAS-1001E Termination Options B.1.2 UDAS Termination and Signal Conditioning OptionsTo UDAS unit I/O ConnectorsFIGURE B.4 UDAS-1001E Termination Options continued Analog In Single-Ended and Differential Function FIGURE B.5 Diagram of the PCI-20430A-1’s connectors and cablesAnalog Analog In SinglePCI-1100 Series Digital Opto-Isolator Blocks Summary of FeaturesB.1.3 Isolator Blocks C.1 UDAS Analog Input Circuit Calibration Procedures Appendix C Analog Input and Output Calibration ProceduresC.1.1 Removing the UDAS Unit’s Cover Equipment RequiredFIGURE C.1 Locations of Potentiometers for Adjusting Analog Circuits Analog Input and Output Calibration ProceduresTP21 R24 R25 R26 R36 TP27Adjust Input Offset Voltage C.1.2 Analog Input Calibration ProcedureAdjust Offset and Gain for ±10Volt Input Range Adjust Offset and Gain for ± 5Volt Input Range Adjust Offset and Gain for 0 to 10 Volt Range Equipment Required C.2 UDAS Analog Output Circuit Calibration ProcedureAnalog Output Channel 1 Offset and Gain Analog Output Channel 0 Offset and GainG gate F featuresIndex U UDAS