Change Default Node Address

Change Default Node Address

This command is used to change the 48 bit physical address associated with any of the attached ports. It also can be used to manage both the factory and user addresses stored in NVRAM, either by setting them to new values, or by restoring preset values.

This command must be issued through the Master Command Entry.

Table 3-27. Change Default Node Address

Change Default Node Address

Offst

15

14

 

13

12

11

10

 

9

 

8

 

7

6

 

5

4

3

2

1

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0x00

 

 

 

 

 

 

 

 

Command Code

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0x01

 

 

 

 

 

 

 

Command Options

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0x02

 

 

 

 

 

 

 

 

Return Status

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0x03

 

Normal Completion Level

 

 

 

 

 

 

Normal Completion Vector

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0x04

 

 

Error Completion Level

 

 

 

 

 

 

 

Error Completion Vector

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0x05

 

 

 

 

 

 

 

 

 

Reserved

 

 

 

 

 

 

 

 

 

to

 

 

 

 

 

 

 

 

 

(10 Bytes)

 

 

 

 

 

 

 

 

0x09

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0x0A

 

 

 

 

 

 

 

Physical Node Address

 

 

 

 

 

 

 

to

 

 

 

 

 

 

 

 

 

(6 Bytes)

 

 

 

 

 

 

 

 

 

0x0C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0x0D

 

 

 

 

 

 

 

 

 

Reserved

 

 

 

 

 

 

 

 

 

to

 

 

 

 

 

 

 

 

 

(10 Bytes)

 

 

 

 

 

 

 

 

0x11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The only change to this IOPB is the addition of a port selector sub-field in the Command options field.

Command Code

This field must contain 0x45 to execute the Change Default Node Address IOPB.

85