Manuals / Iomega / Computer Equipment / Computer Drive

Iomega 03798300 Guide, Check mounting requirements. Your drive bay may require side rails

Models: 03798300

1 48

Download 48 pages 28.74 Kb

Page 12

Image 12

Guide

Installation

3 1/2” drive bays ONLY.

To install your Zip® drive in a 3 1/2” drive bay, remove the mounting screws as illustrated and slide the drive out of the sled.

Check mounting requirements. Your drive bay may require side rails.

MHINT: Check other drives in the system (such as a CD drive) to see if they use mounting rails. If so, you may need similar mounting rails for

the Zip® Internal drive. If the computer does not include extra mounting rails, contact your computer dealer to obtain them. M

51/4" Bay

31/2" Bay

Page 12

Image 12

Iomega 03798300 Guide, Check mounting requirements. Your drive bay may require side rails, 3 1/2” drive bays ONLY

Contents

Installation Guide TroubleshootingHow to Get Help Owner’s ManualTable of Contents Installation GuideTroubleshooting How to Get HelpWelcome to Zip Drive Installation Guide Getting StartedCheck system requirements Unpack the Zip Internal ATAPI driveDISCONNECT the computer power cord and Watch the instructional videoWrite down the serial number of your Zip Internal ATAPI drive for future referenceIdentifying the computer’s IDE configuration Installation GuideCD drive IDE hard drive IDE data cable that extends to the motherboard IDE Channelsidentify your computer’s IDE configuration Locate the IDE channels using the CD drive1b Locate the IDE channels using the computer’s hard drive Follow these instructions if you were unable to1c Possible IDE channel locations Installation GuideIDE Channels IDE channels Determining your computer’s configuration If the hard drive is the only IDE device connectedInstallation Guide Continued on next page …2bIf the CD drive and hard drive are on different IDE channels 2c If the CD drive and hard drive are on the same IDE channelInstallation Guide Installing the Zip drive as the slave, or second device Check the jumper setting on the Zip driveThe Zip Internal drive is set as the factory default to the “slave” panel coverGuide Check mounting requirements. Your drive bay may require side rails3 1/2” drive bays ONLY 4 Slide the Zip drive into the drive bay Remove the IDE Interface cable that iscurrently connected to your CD drive cable from the motherboard and the CD drive and set it asideVerify that the jumper on your CD drive is set to “Master.” Connect the CD drive and the Zip Internal drive to the motherboardZip Internal drive PIN Connect an internal computer power supply cable to the Zip driveSecure drive in drive bay Installation GuideCheck the following items before replacing the computer cover GuideChange the jumper setting to “Master” 2 Locate a vacant 31/2” or 51/4” drive bayInstallation Guide may require side rails 2a3 1/2” drive bays ONLYGuide Check mounting requirements. Your drive bayLocate the data cable that comes packaged with the Zip drive. Find the colored stripe orprint on one side of the data cable showing ConnectorZip drive Connect the other end of the data cable to theGuide cable to your Zip drive Connect an internal computer power supplyInstallation Guide use the power Y-cable provided. Disconnect the power from the CDGuide Check the following items before replacing the computer coverInstalling the IomegaWare Software If the Iomega software setup program doesFollow the screen instructions to install the CD driveAdditional instructions for your system Windows 95/98 UsersWindows NT Users Installation GuideHow to Install Without a CD Drive Create Install Floppy DiskettesIf your drive letters change after installing the Zip Internal drive Download Software from the Iomega Web SiteInstallation Guide 4. Double click the Diskette icon, and follow the screen instructionsAlways turn on power to the computer before inserting a Zip disk Operating Your Zip DriveInserting Zip Disks User’s GuideDisk Eject in Case of Power Loss Ejecting Zip DisksDrive Sleep User’s GuideCompatibility with 100MB Zip Disks User’s GuideZip Tips User’s Guide1-Step Backup/Restore IomegaWare SoftwareRecordIt Software Copy MachineFor information on how to use IomegaWare software Drive ShortcutsUsers with Windows NT Users with Windows 3.1 or Windows for WorkgroupsUsing Zip Disks Backing Up with Zip DisksCopying Zip Disks User’s GuideInstalling Applications to Zip Disks Formatting Zip DisksFormatting Zip Disks under Windows 95/98 or NT User’s GuideSetting Zip Disk Protection under Windows 95/98 and NT Read/Write Protecting Zip DisksUser’s Guide What is IDE? What is ATAPI?Jumper Settings Understanding IDE/ATAPI ConnectionsPossible System IDE/ATAPI Configurations BIOS/CMOS SupportSlave Drive Master DriveTroubleshooting The green activity light on the Zip drive does not turn onTroubleshooting Troubleshooting Data transfer problems or drive operation is erratic Installing the Zip drive changes other drive lettersTroubleshooting You want to change the drive letter assigned to the Zip drive TroubleshootingWindows 95/98 Users Windows 3.1 UsersZip disk won’t eject using Windows NT You can’t change the drive letter assigned to your Zip driveTroubleshooting You want to use Windows 95/98 DOS mode with your Zip drive TroubleshootingHow To Get Help Automated Voice Technical SupportHow to Get Help Automated FAX-back Help 801 778-5763 U.S. & Canada One-on-One Iomega Technical SupportHow To Get Help 1-888-4-IOMEGA is available in the U.S. and CanadaLimited Warranty Information Return or RepairProduct Information International Support NumbersRegulatory Information Model Number Z250ATAPI FCC United StatesCanadian Verification CE European CommunityFree software updates* and cool free software Online Customer Support Product information and specificationsCustomer solutions for educators, businesses, and home Visit our web site