Page 26

Installation

The +12V lead is marked with a red stripe or white lettering; be sure not to reverse the leads.

All connections must be properly insulated to prevent shorting.

5.2.4 (b) JAI Power Cables

When using JAI power cables such as the 12P-02S, please refer to the 12-pin connector pin-out diagram below. The cable pin-out diagram is shown in Figure 40 below. The color-coded leads use Gray for Ground and Yellow for +12V.

FIGURE 40. 12P-02S Interface Cable (optional)

 

 

 

 

 

 

 

 

 

 

 

+12 V

 

 

 

 

 

 

 

 

 

 

 

 

GND (Gray)

 

 

 

 

 

Male

 

 

 

 

 

Power (Yellow)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Video Out (Red Coax)

 

 

Analog Ch. A only

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HD In (White Coax)

}

External sync input

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VD In (Black Coax)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FIGURE 41. 12P-02S Interface Cable Pin Out

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12P-02S Interface Cable

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pin#

Lead Color

Function

 

Pin#

Lead Color

 

 

Function

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

Gray

GND

7

Black coax

 

 

VD Input

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

Yellow

+12V DC

8

White coax shield

 

 

Strobe out

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

Red coax shield

GND (analog)

9

White coax

 

 

HD Input

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

Red coax

Video Out

10

Brown

 

 

RXD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

Orange coax shield

GND (digital)

11

Blue

 

 

Reserved

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

Orange coax

VINIT IN

12

Black coax shield

 

 

TXD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note: Make sure that the unused leads are not touching and that there is no possibility that exposed wires could cause the leads to short.

5.2.4 (c) Building Your Own Power Cable

Refer to the 12-pin connector pin-out in Figure 40 on page 26. Connect the Ground lead to pin #1, and the +12V DC lead to pin #2 of the 12-pin connector. Power must be DC-regulated, and of sufficient current to properly power the camera.

5.2.4 (d) Attaching the Power Cable to the Connector

The 12-pin connector is keyed and will only fit in one orientation. Follow these directions to properly attach the power cable to the camera connector:

1.Rotate the connector while applying slight pressure until the keyways line up.

2.Press the connector into place until firmly seated.

3.Plug the power cord into the 100V AC socket. This will power up the camera.

TM/TMC-4200CL Series Progressive Scan Cameras

Page 36
Image 36
JAI TM/TMC-4200CL JAI Power Cables, 12P-02S Interface Cable Pin# Lead Color Function, Building Your Own Power Cable