JVC HR-S7500U 66EN, TROUBLESHOOTINGcont, Timer Recording, Symptom, Possible Cause, TIMER again

66EN

TROUBLESHOOTING(cont.)

TIMER RECORDING
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	Timer recording won’t work.	● The clock and/or the timer have	Set the clock and/or timer correctly.
		been set incorrectly.
		● The timer is not engaged.	Press TIMER and check to make sure
			that ä appears on the front display
			panel.
		● The VCR has not been set up properly.	Re-perform the set-up procedures.
			Make sure you have compensated for
			Guide Channel and VCR or cable box
			channel number mismatches
			(☞ pg. 47).
2.	Timer programming won’t work.	● Timer recording is in progress.	Timer programming can’t be performed
			when timer recording is in progress.
			Wait until it finishes.
3.	ä and ] on the front display	● The timer is engaged but there’s no	Load a cassette with the record safety
	panel won’t stop blinking.	cassette loaded.	tab intact, or with the hole covered
			with adhesive tape.
4.	The cassette is automatically	● The loaded cassette has had its	Remove the cassette and cover its
	ejected, and ä and ] on the	record safety tab removed.	hole with adhesive tape, or replace it
	front display panel won’t stop		with a cassette on which the safety
	blinking.		tab is intact.
5.	ä blinks for 10 seconds and the	● TIMER has been pressed when there	Check the programmed data and re-
	timer mode is disengaged.	are no programs in memory, or the	program as necessary, then press
		timer record program information	TIMER again.
		has not been programmed correctly.
6.	The cassette is automatically	● The end of tape was reached during	The program may not have been
	ejected, the power shuts off and ä	timer recording.	recorded in its entirety. Next time
	and ] won’t stop blinking.		make sure you have enough time on
			the tape to record the entire program.
7. Cable channels are not automatically		● The Controller is not properly	Connect the Controller correctly
	switched during timer recording.	connected to the VCR.	(☞ pg. 16).
		● The output channel selected in the	After confirming your cable box’s
		Cable Box Set screen is incorrect.	output channel number, re-access the
			Cable Box Set screen and select the
			correct number (☞ pg. 17).
		● The cable box’s power is off.	Make sure the power is on before
			timer recording starts.
8. Satellite channels are not automati-		● The Controller is not properly	Connect the Controller correctly
	cally switched during timer	connected to the VCR.	(☞ pg. 19).
	recording.	● The output channel selected in the	After confirming your DBS receiver’s
		DBS Receiver Set screen is incorrect.	output channel number, re-access the
			DBS Receiver Set screen and select
			the correct number (☞ pg. 20).
		● The VCR is not set correctly to	Set the correct DBS Receiver brand
		control the DBS Receiver	code (☞ pg. 21).
		● The DBS receiver’s power is off.	Make sure the power is on before
			timer recording starts.
9.	Timer recording begins as sched-	● Even though you don't use an	Set "CABLE BOX SET" to "OFF"
	uled, but the channel is always	external Cable Box, "CABLE BOX	(☞ pg. 17).
	incorrect.	SET" is set to "ON".
10.We moved, and now VCR Plus+		● The receivable stations in the new area	Re-perform the VCR Plus+ setup
	doesn’t work properly.	are received on different channels than	procedure (☞ pg. 47).
		those in the previous area.
11.“PROGRAM FULL” is displayed on		● All 8 programs of the VCR’s timer	Wait until a space in memory clears,
	the screen.	memory are used.	or cancel unnecessary program
			information (☞ pg. 51).