72 EN

 

TROUBLESHOOTING (cont.)

 

 

 

 

 

 

 

 

35.

Coloured bright spots appear

35.

•The LCD monitor and the

35.

 

 

 

all over the LCD monitor or the

 

viewfinder are made with

 

 

 

 

viewfinder.

 

high-precision technology.

 

 

 

 

 

 

However, black spots or

 

 

 

 

 

 

bright spots of light (red,

 

 

 

 

 

 

green or blue) may appear

 

 

 

 

 

constantly on the LCD

 

 

 

 

 

monitor or the viewfinder.

 

 

 

 

 

 

These spots are not recorded

 

 

 

 

 

 

on the tape. This is not due to

 

 

 

 

 

 

any defect of the unit.

 

 

 

 

 

 

(Effective dots: more than

 

 

 

 

 

 

99.99 %)

 

 

 

 

 

 

 

 

 

 

36.

The indicators and the image

36.

•This may occur when the

36.

 

 

 

colour on the LCD monitor are

 

surface or the edge of the

 

 

 

not clear.

 

LCD monitor is pressed.

 

 

 

 

 

 

 

 

 

37.

The cassette will not load

37.

•The battery’s charge is low.

37. •Install a fully charged battery.

 

 

properly.

 

 

 

( pg. 10, 11)

 

 

 

 

 

 

 

 

38.

The memory card cannot be

38.

38.

•Push in the memory card a

 

 

removed from the camcorder.

 

 

few more times. ( pg. 17)

 

 

 

 

 

 

 

 

 

 

 

 

 

39.

Picture does not appear on the

39.

•The viewfinder is pulled out

39.

•Push the viewfinder back in

 

 

LCD monitor.

 

and “PRIORITY” is set to

 

or set “PRIORITY” to “LCD”

 

 

 

 

“FINDER”.

 

or “BOTH”.

 

 

 

 

•The LCD monitor’s brightness

 

( pg. 12, 33, 36)

 

 

 

 

setting is too dark.

 

•Adjust the brightness of the

 

 

 

 

 

 

LCD monitor. ( pg. 13)

 

 

 

 

 

 

•If the monitor is tilted

 

 

 

 

 

 

upward 180 degrees, open

 

 

 

 

 

 

the monitor fully. ( pg. 12)

 

 

 

 

 

 

 

 

40.

Images on the LCD monitor

40.

•The speaker volume is too

40.

•Turn the speaker volume

 

 

are jittery.

 

great.

 

down. ( pg. 22)

 

 

 

 

 

 

 

 

41.

The LCD monitor, the

41.

 

41.

•Wipe them gently with soft

 

 

viewfinder and the lens have

 

 

 

cloth. Wiping strongly can

 

 

become dirty (ex. fingerprints).

 

 

cause damage. ( pg. 79) To

 

 

 

 

 

clean the viewfinder, please

 

 

 

 

 

 

 

 

 

 

 

 

consult your nearest JVC

 

 

 

 

 

 

dealer.

 

 

 

 

 

 

 

 

42.

Time code does not appear.

42.

•“TIME CODE” is set to

42.

•Set “TIME CODE” to “ON”.

 

 

 

 

“OFF”.

 

( pg. 33, 37, 40)

 

 

 

 

 

 

 

 

43.

An error indication (E01, E02

43.

•A malfunction of some kind

43.

 pg. 75.

 

 

or E06) appears.

 

has occurred. In this case the

 

 

 

 

 

 

camcorder’s functions

 

 

 

 

 

 

become unusable.

 

 

 

 

 

 

 

 

 

 

44.

An error indication (E03 or

44.

•A malfunction of some kind

44.

 pg. 75.

 

 

E04) appears.

 

has occurred. In this case the

 

 

 

 

 

 

camcorder’s functions

 

 

 

 

 

 

become unusable.

 

 

 

 

 

 

 

 

 

 

45.

The remote control does not

45.

•“REMOTE” is set to “OFF”.

45.

•Set “REMOTE” to “ON”.

 

 

work.

 

•The remote control does not

 

( pg. 33, 36)

 

 

 

 

point at the remote sensor.

 

•Point at the remote sensor.

 

 

 

 

•The remote control batteries

 

( pg. 56)

 

 

 

 

are exhausted.

 

•Replace the batteries with

 

 

 

 

 

 

fresh ones. ( pg. 56)

 

 

 

 

 

 

 

Page 72
Image 72
JVC JY-HD10 manual 72 EN