16 EN INSTALLING YOUR NEW UNIT
Basic Connections |
| THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO | |
| OPERATION CAN BE PERFORMED. | ||
|
| 1 | Make sure the package contains all of the accessories listed in |
|
| 2 | ASPECIFICATIONSB (A pg. 94). |
|
| Place the unit on a stable, horizontal surface. | |
|
| 3 | Connect the unit to a TV depending on the TV and cables you |
|
|
| use. |
| TV aerial cable | 8 | Basic Connection |
| To connect to a TV with | ||
|
| ||
|
| A Disconnect the TV aerial cable from the TV. | |
|
| B Connect the TV aerial cable to the [ANTENNA IN] connector on | |
|
|
| the rear panel of the unit. |
|
| C Connect the [ANTENNA OUT] connector on the rear panel of | |
Mains outlet | To [ANTENNA IN] |
| the unit and the TV’s aerial connector with the supplied RF |
|
| cable. | |
|
|
| |
|
| D Connect the | |
Mains power cord |
|
| unit and the TV’s |
|
|
| pin SCART cable. |
Back of unit |
| ● The | |
|
|
| composite signal (regular video signal), Y/C signal or RGB |
|
|
| signal. |
|
| ● Set your TV to the VIDEO (or AV), Y/C, or RGB mode | |
|
|
| according to the type of your TV’s SCART connector. |
|
|
| 8 Component Video Connection | ||
To [AUDIO | To [COMPONENT | To | To connect to TV’s component video input connectors ^ | ||
VIDEO OUT (Y/PB/ | OUT] | A Perform A – C in ABasic ConnectionB. | |||
OUT] | |||||
PR)] | To | B Connect the unit’s [COMPONENT VIDEO OUT (Y/PB/PR)] | |||
| |||||
|
| [ANTENNA | connectors to the TV’s component video input connectors. | ||
|
| OUT] | C Connect the unit’s [AUDIO OUT] connectors to the TV’s AUDIO | ||
| Component |
| input connectors. |
| |
| ● You can obtain | ||||
Audio cable | video cable | ● If your TV is not | |||
(not supplied) | cable | connectors to connect to an audio amplifier for | |||
(not supplied) | |||||
| (supplied) | ||||
|
| sound reproduction. |
| ||
|
|
|
| ||
|
|
| ● By using the component video connection, you can view the | ||
|
|
| images in the progressive mode. For switching to the | ||
|
|
| progressive mode, refer to AScan Mode SetB (A pg. 89). | ||
|
| RF cable | ● You can also watch the images on the VHS deck in Progressive | ||
|
| (supplied) | scan mode via the component video output, refer to AVHS | ||
|
|
| Progressive ScanB (A pg. 43). |
| |
|
| TV | NOTE: |
| |
|
| To 75 ohm | Select an appropriate option of | ||
|
| (A pg. 72): |
| ||
|
| terminal |
| ||
It’s essential that your unit be properly connected. | When your TV’s SCART | Set | |||
connector accepts: | |||||
| |||||
ATTENTION: |
| Composite signals | ASCART VIDEOB |
|
|
| |
● Your TV must have a |
| Y/C signal (separated |
|
the basic connection to the unit. |
| luminance (brightness) and | ASCART |
● Connect the AC plug only after all connections to the TV has |
| chrominance (colour) signals) |
|
been completed. |
|
|
|
| RGB signal | ASCART RGBB | |
|
| ||
| |||
|
|
|
|
|
| Component video signal | ACOMPONENTB |
When the setting selected is not in accordance with the TV connected and depending on the type of appliance connected to the unit, the correct picture will not appear.
4 Plug the end of the mains power cord into a mains outlet.
● ALOADINGB blinks on the front display panel when the AC plug of the mains power cord is connected into a mains outlet and it takes approximately 50 seconds for the unit to be turned on.
This is not a malfunction.
