92 EN TROUBLESHOOTING
|
| Other Problems | |
Automatic Satellite Programme Recording does not start. | |||
● The satellite receiver is not connected properly to this unit. |
|
| |
| The image of the TV broadcast appears distorted on the TV | ||
N Connect the satellite receiver to the |
| ||
| screen. | ||
connector properly. (A pg. 53) |
| ||
|
| For basic connection | |
On the front display panel, A– | |||
| N Press PROGRESSIVE SCAN for 3 or more seconds so that the | ||
● Power failure occurred. |
| Video output indicator (q) lights off on the front display panel. | |
N Set date and time correctly. (A pg. 86) |
| For component video connection | |
|
| N Press PROGRESSIVE SCAN for 3 or more seconds so that the | |
APROGRAMME FULLB appears on the TV screen during timer | |||
| Video output indicator (q) lights up on the front display panel. | ||
programming. |
| ||
|
| ||
● 32 programmes have already been timer programmed. |
|
| |
| Whistling or howling is heard from the TV during camcorder | ||
N Clear unnecessary programmes on the unit, then try timer |
| recording. | |
programming again. (A pg. 52) |
|
| |
| ● The camcorder’s microphone is too close to the TV. | ||
|
| ||
The disc space does not increase when recorded titles are |
| N Position the camcorder so its microphone is away from the TV. | |
cleared. |
| ● The TV’s volume is too high. | |
● The PC’s data recorded on a |
| N Turn the TV’s volume down. | |
|
| ||
cleared on this unit. |
|
| |
| When scanning channels, some of them are skipped over. | ||
N Format the disc. (When the disc is soiled, wipe the disc with a |
| ||
soft dry cloth before formatting.) (A pg. 9, 87) |
| ● Those channels have been designated to be skipped. | |
Timer Recording (VHS Deck) |
| N If you need the skipped channels, restore them. (A pg. 84) | |
|
| ||
|
| The channel cannot be changed. | |
|
|
|
Timer programming cannot be made.
●Date and time is not correct.
NSet date and time correctly. (A pg. 86)
● The timer is not engaged.
N Press VHSj and confirm that the VHS timer indicator lights up on the front display panel.
● Timer recording is in progress.
N Timer programming can’t be performed while a timer recording is in progress. Wait until it finishes.
Timer programming recording does not start.
●Date and time is not correct.
NSet date and time correctly. (A pg. 86)
● The timer is not engaged.
N Press VHSj and confirm that the VHS timer indicator lights up on the front display panel.
The VHS recording lamp on the unit won’t stop blinking.
●Recording or RetroActive recording* is in progress.
NPress W to pause recording, change the channel, then press I to resume recording.
*HDD deck only
Channel settings that were made manually seem to have changed or disappeared.
●After the manual settings were made, Auto Channel Set was performed.
NPerform AClock SetB (A pg. 86).
Malfunction occurs and the unit cannot be power off.
NReset the unit by disconnecting the AC power plug from the AC outlet and connect again.
●The timer is engaged but there’s no cassette loaded. N Load a cassette with the record safety tab intact.
●The loaded cassette has had its record safety tab removed.
N Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the record safety tab intact.
aTimer Programming cannot be made.
●Date and time set on the unit is not correct. N Set date and time correctly. (A pg. 86)
●The channel position does not correspond to that in the receiving area.
NSet the correct channel position for the receiving broadcast. (A pg. 83)
The asystem does not timer-record properly.
●The unit’s channel positions have been set incorrectly.
NRefer to AcSystem SetupB (A pg. 83) and
