JVC CX-7000 Series, LST1006-002A m, m

mFilm Type

Displays the specification of the loaded retransfer film in the number of

images. This is not an indication of the current film level.

m[Update] button

Applies the selected value to the printer.

m[Refresh] button

Displays the printer settings on the screen.

mInk ribbon cannot be recognized

If the ink ribbon cannot be recognized, the cause for this problem is

indicated in the [Name] field under [Ink Status].

.

Message Cause and Action During Ink

Recognition Error

(252:Invalid TAG

Data)

The TAG record data adhered to the ink

ribbon is incorrect. Replace the ink ribbon

and try again.

(253:Defective

TAG)

Unable to establish communication with

the TAG adhered to the ink ribbon.

Replace the ink ribbon and try again.

(254:No TAG) Unable to read the TAG adhered to the ink

ribbon. Check to ensure that the ink ribbon

is correctly set.

(255:Defective R/

W)

Printer TAG reader error. The printer

needs to be repaired.

[Property] Tab

This tab displays the device configuration.

.

mOptional Unit Configuration

Displays the configuration of optional devices.

Cautions:

vIf a setting other than [None] is displayed for the contact or non-

contact IC encoder, it means the configuration supports installation

of an IC encoder, and is not an indication that an IC encoder has

been installed.

vConsult our authorized dealers on how to install the IC encoder.

mVersion

Displays the firmware version of the printer and laminator. If a

laminator is not connected, [????????] will appear.

mCounter

Displays the counter value of the printer.

mPrint Counter (free counter)

Displays the total number of cards that are correctly printed.

Memo:

vClicking [Clear] for “Print Counter” in the [Printer Status] Tab

resets the counter value of the [Print Counter] to 0.

"Print Counter" (A page 109)

mCleaning Counter

Displays the number of cards that are correctly printed after the last

cleaning.

mError Counter

Displays the number of cards that are not correctly printed.

Memo:

vClicking [Clear] for “Print Counter” in the [Printer Status] Tab

resets the counter value of the [Error Counter] to 0.

"Print Counter" (A page 109)

mPrinter Total Counter (total counter)

Displays the number of cards that are correctly printed.

mThermal Head (head counter)

Displays the number of print ink panels for the thermal head.

For example, when printing on a single side using all YMCK inks, 4

are added to each card.

Setup

113

Contents

Main CX-7000 Series Contents About this Manual Contents of this Manual Batch Print How to Read this Manual Print Page Page Precautions During Use Printer Installation Precautions on Retransfer Film/Ink Ribbon/Card Precautions on Retransfer Film/Ink Ribbon Precautions on Cards Disclaimer Name and Functions of Parts Internal Mechanism Diagram Front Rear Right Left When Printer Door is Open Ink Ribbon Cassette Retransfer Film Cassette Specifications Main Specifications Outline Dimensional Drawing Accessories/Products Sold Separately Accessories Options Options Printing a Card 1 2 3 4 Exit Menu Scroll Next Enter Page Setting Mode Cleaning Counter Reset Download Transport Mode Bend Remedy Heat Roller Option MG Network 2 Page Factory Settings m Security Lock Registration of Security Key Number 3 4 5 3 4 Deleting the Security Key Number 2 3 4 5 Setting Using the Operation Panel Initialization 1 Initializing Printer When Installing the Cassette 2 3 4 5 Firmware Update 2 4 5 6 Display Mode Setting 2 4 5 6 7 8 2 4 5 Page Page Page Page Page Cards Cards have Run Out 1 2 3 Ink Ribbon Ink Ribbon has Run Out 2 3 4 Retransfer Film Retransfer Film has Run Out 2 3 4 Servicing of Parts Cleaning Roller 2 3 4 1 2 3 Fan Filter 1 2 4 5 Card Feed Roller/Heating Roller 1 2 3 4 5 6 9 10 11 12 Magnetic Head 1 2 3 4 5 9 Bobbin Holders 3 4 5 6 Thermal Head Page Servicing Based on Print Output When an Error Message is Displayed List of Error Codes No Card Jam(Hopper) 90 Jam(TurnOver) 91 Ink Run Out B2 Hardware 44 MG Mechanical AB MG Hardware AC Cam Error C1 Cards Cards have Run Out Card Jam Error Code Jam(Hopper) 90 1 1 2 3 4 5 6 7 8 9 10 Error Code Jam(MG) 92 Error Code Jam(Transfer) 93 Error Code Jam(Discharge) 94 Error Code Jam(Retran.) 95 2 3 4 5 6 Page Ink Ribbon Ink Ribbon has Run Out Ink Ribbon is Broken 3 Page Retransfer Film Retransfer Film has Run Out Retransfer Film is Broken 2 3 Unable to Produce Desired Printing Results Lines Appear on Card after Printing Colors on Card Appear Faded after Printing Peeling Occurs on Card after Printing Overall Printing Quality is Poor Printer not Operating as Desired Card is not Fed into the Printer Power does not Turn On Printing does not Start or Stops Halfway Before Sending Printer for Repair Installation and Connection Printer Installation Power Cord Connection 1 2 Printing Media Installing the Ink Ribbon 3 4 Installing the Retransfer Film 2 3 4 Setting Cards 1 2 3 4 Printer and Computer Connection Connecting with a USB Cable 1 2 3 Connecting with a LAN Cable Computer Settings Software Software License Agreement Install Printer Driver Installing the Printer Driver USB Connection 2 4 7 8 9 10 11 12 13 14 15 16 Ethernet (LAN) Connection 2 4 6 7 8 9 10 11 12 13 14 15 16 Update of Printer Driver To update 1 2 1 2 4 5 6 1 2 3 4 5 2 4 6 7 Update of Status Monitor 1 2 USB Driver Installing the USB Driver Page Page Electronic Manual Installing the Electronic Manual 2 4 6 7 Uninstall 2 3 4 7 9 Ethernet (LAN) Connection 2 3 7 9 Status Monitor Uninstalling the Status Monitor 1 2 3 4 5 Electronic Manual Uninstalling the Electronic Manual 1 2 3 4 IPSec Setting Procedures Printer01.pfx 1 2 Page Certification Authority Certificate File 1 2 Printer Driver Settings m m m m m Setting Example [Setup] Tab m Page [Printing area] Dialog Box m Page [Dither] Dialog Box m [UV ink] Dialog Box m A m BD Priority of printing data Page Number for the Printed Document and Page Split Settings B C A Windows Bitmap File Format Number of retransfer film panels during printing m [Encode] Tab m [Configuration] Tab m [Version] Tab Page Page Page Double-sided Printing (Single-side Lamination) Single-sided UV Printing Page Split Page Encoding and Printing (ISO Card) Encoding and Printing (JIS Card) Page Port Monitor Settings [Property] Tab m [Version] Tab Status Monitor Settings m m Executing the status monitor Screen Configuration [Printer Status] Tab m [Printer Setting] Tab m [Retransfer] Tab m [Bend Remedy] Tab m [Media Setting] Tab m [Property] Tab m [Printer Select] Tab m 1 2 3 1 2 3 4 5 1 m 2 3 m Inline Encoding Format A CB Character Code List string to encode using the usable half-width characters for each of the unit codes. the encoding data. Unit Code Start Sentinel (Hexadecimal) End Sentinel (Hexadecimal) 4-unit code ; (3B) ? (3F) 6-unit code List of Error Codes Printer (Error Code:0x01000000-0x01040000) Printer (Error Code:0x01040000-0x02000000) Printer Driver (Error Code:0x02000000-) Frequently Asked Questions C Printing Settings The edge of the image is not printed B The card is discharged without being printed