JVC CX-7000 Series, LST1006-002A m, m

mIC

mNon-contact IC encode

Allows writing of data to a non-contact IC.

mContact IC encode

Allows writing of data to a contact IC.

mTurns over the card after IC encoding

Turns over the card after writing data to the non-contact/contact

IC.

mMagnetic

mMagnetic encode

Allows writing of data to the magnetic stripe.

mTurns over the card after MG encoding

Turns over the card after writing data to the magnetic stripe.

mWrite Retry

For setting the maximum number of retries when writing to or

reading of the magnetic stripe fails.

When the [Default] is selected, the retry counter uses the preset

value of the printer.

mCoercivity

Coercivity of the magnetic stripe card.

When the [Default] is selected, the coercivity uses the preset value

of the printer.

mStarts from magnetic encoding

Unchecked : Encodes in the ICNMagnetic sequence.

Checked : Encodes in the MagneticNIC sequence.

mPrints after encoding

Unchecked : Starts printing while encoding is in progress.

Checked : Starts printing after encoding is complete.

[Configuration] Tab

.

Memo:

vThese settings can be altered only when the user logs into the

printer driver settings page with administrator authority

(Administrators group).

This tab is displayed in the read-only mode when a user without

administrator authority logs in.

mOptional configuration

For specifying whether the options are installed.

mTurn over unit

mBend remedy unit

mNon-contact IC encoder

mISO Contact IC encoder

mJIS Contact IC encoder

mISO Magnetic encoder

mJIS Magnetic encoder

mLaminator

mEnable the settings

Permits or forbids the [Enable the printer settings] functions in the

[Print] tab.

mPrinter settings

Unchecked : Forbids the [Enable the printer settings] functions in

the [Print] tab.

Checked : Permits the [Enable the printer settings] functions in

the [Print] tab.

"Enable the printer settings" (A page 88)

Cautions:

vWhen a user logs in with administrator authority (Administrators

group), the [Configuration] settings can be specified.

If a user logs in without administrator authority, the [Configuration]

settings appear in the read-only mode, and they cannot be specified.

[Version] Tab

Displays the version and copyright information.

.

Setup

95

Contents

Main CX-7000 Series Contents About this Manual Contents of this Manual Batch Print How to Read this Manual Print Page Page Precautions During Use Printer Installation Precautions on Retransfer Film/Ink Ribbon/Card Precautions on Retransfer Film/Ink Ribbon Precautions on Cards Disclaimer Name and Functions of Parts Internal Mechanism Diagram Front Rear Right Left When Printer Door is Open Ink Ribbon Cassette Retransfer Film Cassette Specifications Main Specifications Outline Dimensional Drawing Accessories/Products Sold Separately Accessories Options Options Printing a Card 1 2 3 4 Exit Menu Scroll Next Enter Page Setting Mode Cleaning Counter Reset Download Transport Mode Bend Remedy Heat Roller Option MG Network 2 Page Factory Settings m Security Lock Registration of Security Key Number 3 4 5 3 4 Deleting the Security Key Number 2 3 4 5 Setting Using the Operation Panel Initialization 1 Initializing Printer When Installing the Cassette 2 3 4 5 Firmware Update 2 4 5 6 Display Mode Setting 2 4 5 6 7 8 2 4 5 Page Page Page Page Page Cards Cards have Run Out 1 2 3 Ink Ribbon Ink Ribbon has Run Out 2 3 4 Retransfer Film Retransfer Film has Run Out 2 3 4 Servicing of Parts Cleaning Roller 2 3 4 1 2 3 Fan Filter 1 2 4 5 Card Feed Roller/Heating Roller 1 2 3 4 5 6 9 10 11 12 Magnetic Head 1 2 3 4 5 9 Bobbin Holders 3 4 5 6 Thermal Head Page Servicing Based on Print Output When an Error Message is Displayed List of Error Codes No Card Jam(Hopper) 90 Jam(TurnOver) 91 Ink Run Out B2 Hardware 44 MG Mechanical AB MG Hardware AC Cam Error C1 Cards Cards have Run Out Card Jam Error Code Jam(Hopper) 90 1 1 2 3 4 5 6 7 8 9 10 Error Code Jam(MG) 92 Error Code Jam(Transfer) 93 Error Code Jam(Discharge) 94 Error Code Jam(Retran.) 95 2 3 4 5 6 Page Ink Ribbon Ink Ribbon has Run Out Ink Ribbon is Broken 3 Page Retransfer Film Retransfer Film has Run Out Retransfer Film is Broken 2 3 Unable to Produce Desired Printing Results Lines Appear on Card after Printing Colors on Card Appear Faded after Printing Peeling Occurs on Card after Printing Overall Printing Quality is Poor Printer not Operating as Desired Card is not Fed into the Printer Power does not Turn On Printing does not Start or Stops Halfway Before Sending Printer for Repair Installation and Connection Printer Installation Power Cord Connection 1 2 Printing Media Installing the Ink Ribbon 3 4 Installing the Retransfer Film 2 3 4 Setting Cards 1 2 3 4 Printer and Computer Connection Connecting with a USB Cable 1 2 3 Connecting with a LAN Cable Computer Settings Software Software License Agreement Install Printer Driver Installing the Printer Driver USB Connection 2 4 7 8 9 10 11 12 13 14 15 16 Ethernet (LAN) Connection 2 4 6 7 8 9 10 11 12 13 14 15 16 Update of Printer Driver To update 1 2 1 2 4 5 6 1 2 3 4 5 2 4 6 7 Update of Status Monitor 1 2 USB Driver Installing the USB Driver Page Page Electronic Manual Installing the Electronic Manual 2 4 6 7 Uninstall 2 3 4 7 9 Ethernet (LAN) Connection 2 3 7 9 Status Monitor Uninstalling the Status Monitor 1 2 3 4 5 Electronic Manual Uninstalling the Electronic Manual 1 2 3 4 IPSec Setting Procedures Printer01.pfx 1 2 Page Certification Authority Certificate File 1 2 Printer Driver Settings m m m m m Setting Example [Setup] Tab m Page [Printing area] Dialog Box m Page [Dither] Dialog Box m [UV ink] Dialog Box m A m BD Priority of printing data Page Number for the Printed Document and Page Split Settings B C A Windows Bitmap File Format Number of retransfer film panels during printing m [Encode] Tab m [Configuration] Tab m [Version] Tab Page Page Page Double-sided Printing (Single-side Lamination) Single-sided UV Printing Page Split Page Encoding and Printing (ISO Card) Encoding and Printing (JIS Card) Page Port Monitor Settings [Property] Tab m [Version] Tab Status Monitor Settings m m Executing the status monitor Screen Configuration [Printer Status] Tab m [Printer Setting] Tab m [Retransfer] Tab m [Bend Remedy] Tab m [Media Setting] Tab m [Property] Tab m [Printer Select] Tab m 1 2 3 1 2 3 4 5 1 m 2 3 m Inline Encoding Format A CB Character Code List string to encode using the usable half-width characters for each of the unit codes. the encoding data. Unit Code Start Sentinel (Hexadecimal) End Sentinel (Hexadecimal) 4-unit code ; (3B) ? (3F) 6-unit code List of Error Codes Printer (Error Code:0x01000000-0x01040000) Printer (Error Code:0x01040000-0x02000000) Printer Driver (Error Code:0x02000000-) Frequently Asked Questions C Printing Settings The edge of the image is not printed B The card is discharged without being printed