JVC RX-8040B manual Operating Other Manufacturers’ Equipment

TV

CATV/

DBS

Operating Other Manufacturers’ Equipment

This remote control supplied with the receiver can transmit control signals for other manufacturers’ TVs, CATV converters, DBS tuners, VCRs and DVD players.

•Refer also to the manuals supplied with your video components.

English

IMPORTANT:

•To operate the other component(s) using the RF signals emitted from this remote control, the IR signal transmitter and the RF rod antenna must be connected to this receiver.

–Place the IR signal transmitter so that it is aimed at the remote sensor(s) on the target component(s).

–The RF signal-reachable distance may differ depending on the operating conditions and circumstances.

–The IR signal transmitter can send signals at a distance of 3 m.

When using the remote control:

By changing the transmittable signals from preset ones to the other manufacturers’, you can operate the other manufacturer’s components using this remote control.

To change the transmittable signals for operating another manufacturer’s TV

1. Set the TV operation mode selector to TV.

TV/CATV/DBS

POWER

–Set the ZONE 1/ZONE 2 selector to ZONE 1 or ZONE 2 correctly.

ZONE 1 ZONE 2	ZONE 1 ZONE 2
Ex. When you set ZONE 1/	Ex. When you set ZONE 1/
ZONE 2 selector to ZONE 1.	ZONE 2 selector to ZONE 2.

2.Press and hold

TV/CATV/DBS POWER.

3.Press TV/DBS.

TV/DBS

4.Enter a manufacturer’s code using buttons 1–9, and 0.

1 2 3

4 5 6

7/P 8 9

–Set the TV operation mode selector to TV or

CATV/DBS correctly.

See page 62 to find the code.

10 0 +10

RETURN

To operate the TV, set it to TV.

To operate the CATV converter or DBS tuner, set it to CATV/DBS.

–Check the indication shown on the remote’s display when you press a button—this indicates the remote control operation mode together with multi-room operation mode (either for ZONE 1 or ZONE 2) for about two hours.

		AUDIO POWER				AUDIO POWER
ZONE 1	ZONE 2	STANDBY	ON	ZONE 1	ZONE 2	STANDBY	ON
ZONE 1	ZONE 2	TV/CATV/DBS	DVD	ZONE 1	ZONE 2	TV/CATV/DBS	DVD
ON/OFF	ON/OFF	POWER	POWER	ON/OFF	ON/OFF	POWER	POWER
	ZONE 1					ZONE 2

5.Release

TV/CATV/DBS POWER.

6.Try to operate your TV by pressing

TV/CATV/DBS POWER.

When your TV turns on or off, you have entered the correct code.

If more than one code is listed for

your brand of TV, try each one until the correct one is entered.

TV

TV/VIDEO

TV VOL CHANNEL

Ex. When you press DVD with	Ex. When you press DVD with
ZONE 1/ZONE 2 selector	ZONE 1/ZONE 2 selector
set to ZONE 1.	set to ZONE 2.

Note:

When replacing the batteries, finish changing them without delay; otherwise, preset manufacturers’ codes will be reset.

After setting the TV operation mode

selector to TV, you can perform the following operations on the TV:

TV/CATV/DBS POWER

	: Turn on or off the TV.
TV VOL +/–	: Adjust the volume.
TV/VIDEO	: Set the input mode (either TV or
	VIDEO).

After pressing TV/DBS (with the TV operation mode selector set to TV), you can perform the following operations on the TV:

CHANNEL +/–	: Change the channels.
1 – 9, 0, 100+ (+10)	: Select the channels.
10 (RETURN)	: Alternates between the previously
	selected channel and the current
	channel.
Notes:

•Refer to the manual supplied for the TV.

•Some buttons listed above may not be used for some TVs.

•If you cannot change the channels of some TVs by pressing number buttons, press the CHANNEL +/– buttons.

59