Standard Setup, Date/Time, Floppy Drive A, B | Intel Raptor AT

Raptor AT – Installation Guide

functions are described in this chapter. Some options may not be available in your BIOS. The windows are:

•Standard CMOS Setup

•Advanced CMOS Setup

•Advanced Chipset Setting

•Power Management Setup

•PCI/Plug and Play Setup

•Peripheral Setup

•Auto-Detect Hard Drive

•Change User Password

•Change Supervisor Password

•Change Language Settings

•Auto Configuration with Optimal Settings

•Auto Configuration with Fail Safe Settings

•Save Settings and Exit

•Exit Without Saving

Standard Setup

Standard Setup options are displayed by choosing Standard option from the HIFLEX BIOS Setup menu. All Standard Setup options are described below.

Date/Time

Select the Date/Time option to change the date or time. The current date and time are displayed. Enter new values through the displayed window.

Floppy Drive A, B

Choose either Floppy Drive A or B to specify the floppy drive

type. The settings are 360 KB 5¼", 1.2 MB 5¼", 720 KB 3½", 1.44 MB 3½" and 2.88 MB 3½".

16

Image 26

Intel Raptor AT manual Standard Setup, Date/Time, Floppy Drive A, B

Contents

Raptor AT Page Pre-Configuration Chapter Appendix a Technical Specifications Appendix B Flash Bios Programming Appendix C Disk-On-Chip Appendix D On-Board Industrial Appendix E On-Board Raptor AT Installation Guide System Board Pre-Configuration Introduction Static Electricity Warning Memory CPU SupportSupported Bus Clocks On-Board I/O Conventions Used in this Manual On-Board Ethernet Pre-Configuration Static Warning Raptor AT Installation Guide Jumper Types Jumper Locations Jumper Locations Flash Bios Write Protect Cmos ResetReset Cmos Normal Clear Cmos Flash Write-protect Enabled Disabled Clock Speed Selection Watchdog Timer SelectionTimeout Clock JP11 Address 110h Closed Open 310h Ethernet Selection Enabled DisabledATX Power Supply Enhancements Raptor AT Memory Configuration CPU Installation Designing for thermal performance Fan Heatsink Installing Peripheral Cables Disk-on-Chip installationInstalling Cables Power and Control Panel Cables Airflow management Pre-Configuration Location of Components and Connectors Index of Connectors Connector Description Users Notes Using the Keyboard with Bios Setup SetupStarting Bios Setup Bios Setup Main Menu Floppy Drive A, B Standard SetupDate/Time Quick Boot Advanced Cmos SetupBoot Sector Virus Protection Pri Master Pri Slave Sec Master Sec Slave Floppy Access Control Try Other Boot DevicesInitial Display Mode Hard Disk Access Control Floppy Drive Swap Boot Up Num LockA.R.T. for Hard Disks Floppy Drive Seek Wait for F1 If Error Password CheckBoot to OS/2 Primary Display Internal Cache Advanced Chipset SetupSystem Bios Cacheable C000,16K Shadow C400,16K Shadow PCI 1 to PCI 0 Access BX/GX Master Latency Timer ClksMulti-Trans Timer Clks USB KB/Mouse Legacy Support Dram Integrity Mode Aperture Access Global EnablePCI 0 Agent to Aperture Access Memory Autosizing Support Sdram RAS# to CAS# Delay 16bit I/O Recovery Time Power Down SdramSearch for MDA Resources Bit I/O Recovery Time Sdram Precharge Control Power Management Setup Green PC Monitor Power State Power Management/APMPower button Function Video Power Down Mode Standby Timeout Power Saving TypeStandby / Suspend Timer Unit Suspend Timeout LAN Wake-Up PCI/Plug and Play SetupPCI Latency Timer PCI Clocks Plug and Play Aware OS PCI IDE Bus Master PCI VGA Palette SnoopAllocate IRQ to PCI VGA Off-board PCI IDE Card Off-board PCI IDE Secondary IRQ DMA Channel Reserved Memory Address Peripheral SetupReserved Memory Size PCI Device Search Order Parallel Port Mode Serial Port2 ModeInfra-Red Transmission Mode Onboard Serial Port1 EPP Version CPU Current TemperatureCPU Overheat Warning Temperature Parallel Port IRQ CPU Fan Secondary Fan Change User PasswordAuto Detect Hard Disk Onboard IDE Change Supervisor Password Exit without Saving Auto Configuration with Fail-Safe SettingsSave Settings and Exit Upgrading the Microprocessor Chapter UpgradingUpgrading the System Memory Users Notes System Memory BiosAppendix a Embedded I/O Industrial Devices Miscellaneous Form Factor Control Panel ConnectionsCPU Socket PCB Construction Address Range Size Description Decimal Hexadecimal Memory MapDMA Channels Data Width System Resource Map Address hex Description Bus # Device # Function # Description PCI Configuration Space MapOn-board Devices PCI Interrupt Routing Map SignalInterrupts Connectors Pin-out Device Slave Address Pin# Serial Ports DB9M J36 and J37 Ethernet Header J31 Pin# Parallel DB25F J13 Pin# HDD LED Appendix B Flash Bios Programming Beeps Description Appendix C Disk-On-Chip Users Notes Software Reset Watchdog TimerHardware Reset Appendix D On-Board Industrial Devices Address Post Code Display Post Checkpoint Codes Checkpoint Description Code Table D-5 Bootblock Recovery Codes Table D-6 Uncompressed Initialization Codes Memory refresh line is toggling. Checking 3Ah Performing the DMA controller 2 base register test next Winbios Adaptor ROM had control and has now returned Table D-7 Bus Checkpoint Codes Bits Description Appendix E On-Board Ethernet Users Notes Page MN-RBXAT-03