Primary Display, Password Check, Boot to OS/2 | Intel Raptor AT

Raptor AT – Installation Guide

Primary Display

This option configures the type of video card attached to the computer. The settings are Mono, CGA40x25, CGA80x25, VGA/EGA (default) and Absent. Use Absent for systems without video cards.

Password Check

This option enables password checking every time the system boots or when you run AMIBIOS Setup. If Always is chosen, a user password prompt appears every time the computer is turned on. If Setup is chosen, the password prompt appears if AMIBIOS is executed. See the Advanced Setup chapter for instructions on changing a password. The Optimal and Fail-Safe default is Setup.

BOOT to OS/2

Set this option to Enabled if running OS/2 operating system and using more than 64 MB of system memory on the motherboard. The setting is either Yes or No (default).

Wait for <F1> If Error

If this option is set to Enabled, AMIBIOS waits for the user to press <F1> before continuing. If this option is set to Disabled, AMIBIOS continues the boot process without waiting for <F1> to be pressed.

Hit Del Message Display

Set this option to Disabled to prevent the message

Hit <DEL> if you want to run Setup

from appearing on the first AMIBIOS screen when the computer boots. The setting is either Disabled or Enabled. The Optimal and Fail-Safe default setting is Enabled.

20

Image 30

Intel Raptor AT manual Primary Display, Password Check, Boot to OS/2, Wait for F1 If Error, Hit Del Message Display

Contents

Raptor AT Page Pre-Configuration Chapter Appendix a Technical Specifications Appendix B Flash Bios Programming Appendix C Disk-On-Chip Appendix D On-Board Industrial Appendix E On-Board Raptor AT Installation Guide System Board Pre-Configuration Introduction Static Electricity Warning Memory CPU SupportSupported Bus Clocks On-Board I/O Conventions Used in this Manual On-Board Ethernet Pre-Configuration Static Warning Raptor AT Installation Guide Jumper Types Jumper Locations Jumper Locations Flash Bios Write Protect Cmos ResetReset Cmos Normal Clear Cmos Flash Write-protect Enabled Disabled Clock Speed Selection Watchdog Timer SelectionTimeout Clock JP11 Ethernet Selection Enabled Disabled ATX Power Supply EnhancementsAddress 110h Closed Open 310h Raptor AT Memory Configuration CPU Installation Designing for thermal performance Fan Heatsink Installing Peripheral Cables Disk-on-Chip installationInstalling Cables Power and Control Panel Cables Airflow management Pre-Configuration Location of Components and Connectors Index of Connectors Connector Description Users Notes Using the Keyboard with Bios Setup SetupStarting Bios Setup Bios Setup Main Menu Standard Setup Date/TimeFloppy Drive A, B Quick Boot Advanced Cmos SetupBoot Sector Virus Protection Pri Master Pri Slave Sec Master Sec Slave Floppy Access Control Try Other Boot DevicesInitial Display Mode Hard Disk Access Control Floppy Drive Swap Boot Up Num LockA.R.T. for Hard Disks Floppy Drive Seek Wait for F1 If Error Password CheckBoot to OS/2 Primary Display Internal Cache Advanced Chipset SetupSystem Bios Cacheable C000,16K Shadow C400,16K Shadow PCI 1 to PCI 0 Access BX/GX Master Latency Timer ClksMulti-Trans Timer Clks USB KB/Mouse Legacy Support Dram Integrity Mode Aperture Access Global EnablePCI 0 Agent to Aperture Access Memory Autosizing Support Sdram RAS# to CAS# Delay 16bit I/O Recovery Time Power Down SdramSearch for MDA Resources Bit I/O Recovery Time Sdram Precharge Control Power Management Setup Green PC Monitor Power State Power Management/APMPower button Function Video Power Down Mode Standby Timeout Power Saving TypeStandby / Suspend Timer Unit Suspend Timeout LAN Wake-Up PCI/Plug and Play SetupPCI Latency Timer PCI Clocks Plug and Play Aware OS PCI IDE Bus Master PCI VGA Palette SnoopAllocate IRQ to PCI VGA Off-board PCI IDE Card Off-board PCI IDE Secondary IRQ DMA Channel Reserved Memory Address Peripheral SetupReserved Memory Size PCI Device Search Order Parallel Port Mode Serial Port2 ModeInfra-Red Transmission Mode Onboard Serial Port1 EPP Version CPU Current TemperatureCPU Overheat Warning Temperature Parallel Port IRQ CPU Fan Secondary Fan Change User PasswordAuto Detect Hard Disk Onboard IDE Change Supervisor Password Auto Configuration with Fail-Safe Settings Save Settings and ExitExit without Saving Chapter Upgrading Upgrading the System MemoryUpgrading the Microprocessor Users Notes Bios Appendix aSystem Memory Embedded I/O Industrial Devices Miscellaneous Form Factor Control Panel ConnectionsCPU Socket PCB Construction Address Range Size Description Decimal Hexadecimal Memory MapDMA Channels Data Width System Resource Map Address hex Description PCI Configuration Space Map On-board DevicesBus # Device # Function # Description Signal InterruptsPCI Interrupt Routing Map Connectors Pin-out Device Slave Address Pin# Serial Ports DB9M J36 and J37 Ethernet Header J31 Pin# Parallel DB25F J13 Pin# HDD LED Appendix B Flash Bios Programming Beeps Description Appendix C Disk-On-Chip Users Notes Software Reset Watchdog TimerHardware Reset Appendix D On-Board Industrial Devices Address Post Code Display Post Checkpoint Codes Checkpoint Description Code Table D-5 Bootblock Recovery Codes Table D-6 Uncompressed Initialization Codes Memory refresh line is toggling. Checking 3Ah Performing the DMA controller 2 base register test next Winbios Adaptor ROM had control and has now returned Table D-7 Bus Checkpoint Codes Bits Description Appendix E On-Board Ethernet Users Notes Page MN-RBXAT-03