PCI/Plug and Play Setup, LAN Wake-Up | Intel Raptor AT specs

Raptor AT – Installation Guide

Device 0 (Primary Master IDE)

Device 1 (Primary Slave IDE)

Device 2 (Secondary Master IDE)

Device 3 (Secondary Slave IDE)

When set to Monitor, this option enables event monitoring on the device. If set to Monitor and the computer is in a power saving state, AMIBIOS watches for activity. The computer enters the Full On state if any activity occurs. AMIBIOS reloads the Standby and Suspend timeout timers if device activity occurs. The settings are either Monitor or Ignore.

LAN Wake-Up

The settings for this option are: Disabled (default) and Enabled.

PCI/Plug and Play Setup

PCI/PnP Setup options are displayed by choosing the PCI/PnP Setup from the AMIBIOS Setup main menu. All PCI/PnP Setup options are described in this section.

Plug and Play Aware OS

Set this option to Yes if the operating system installed in the computer is Plug and Play-aware. AMIBIOS only detects and enables PnP ISA adapter cards that are required for system boot. The Windows 95 and 98 operating systems detect and enable all other PnP-aware adapter cards. Windows 95 is PnP-aware. Set this option to No if the operating system (such as DOS, OS/2, Windows 3.x) does not use PnP. You must set this option correctly or PnP-aware adapter cards installed in your computer will not be configured properly. The setting is either No or Yes. The Optimal and Fail-Safe default setting is No.

PCI Latency Timer (PCI Clocks)

This option sets latency of all PCI devices on the PCI bus. The settings are in units equal to PCI clocks. The settings are 32, 64,

28

Image 38

Intel Raptor AT manual PCI/Plug and Play Setup, LAN Wake-Up, Plug and Play Aware OS, PCI Latency Timer PCI Clocks

Contents

Raptor AT Page Pre-Configuration Chapter Appendix a Technical Specifications Appendix B Flash Bios Programming Appendix C Disk-On-Chip Appendix D On-Board Industrial Appendix E On-Board Raptor AT Installation Guide System Board Pre-Configuration Introduction Static Electricity Warning Memory CPU SupportSupported Bus Clocks On-Board I/O Conventions Used in this Manual On-Board Ethernet Pre-Configuration Static Warning Raptor AT Installation Guide Jumper Types Jumper Locations Jumper Locations Flash Bios Write Protect Cmos ResetReset Cmos Normal Clear Cmos Flash Write-protect Enabled Disabled Clock Speed Selection Watchdog Timer SelectionTimeout Clock JP11 Address 110h Closed Open 310h Ethernet Selection Enabled DisabledATX Power Supply Enhancements Raptor AT Memory Configuration CPU Installation Designing for thermal performance Fan Heatsink Installing Peripheral Cables Disk-on-Chip installationInstalling Cables Power and Control Panel Cables Airflow management Pre-Configuration Location of Components and Connectors Index of Connectors Connector Description Users Notes Using the Keyboard with Bios Setup SetupStarting Bios Setup Bios Setup Main Menu Floppy Drive A, B Standard SetupDate/Time Quick Boot Advanced Cmos SetupBoot Sector Virus Protection Pri Master Pri Slave Sec Master Sec Slave Floppy Access Control Try Other Boot DevicesInitial Display Mode Hard Disk Access Control Floppy Drive Swap Boot Up Num LockA.R.T. for Hard Disks Floppy Drive Seek Wait for F1 If Error Password CheckBoot to OS/2 Primary Display Internal Cache Advanced Chipset SetupSystem Bios Cacheable C000,16K Shadow C400,16K Shadow PCI 1 to PCI 0 Access BX/GX Master Latency Timer ClksMulti-Trans Timer Clks USB KB/Mouse Legacy Support Dram Integrity Mode Aperture Access Global EnablePCI 0 Agent to Aperture Access Memory Autosizing Support Sdram RAS# to CAS# Delay 16bit I/O Recovery Time Power Down SdramSearch for MDA Resources Bit I/O Recovery Time Sdram Precharge Control Power Management Setup Green PC Monitor Power State Power Management/APMPower button Function Video Power Down Mode Standby Timeout Power Saving TypeStandby / Suspend Timer Unit Suspend Timeout LAN Wake-Up PCI/Plug and Play SetupPCI Latency Timer PCI Clocks Plug and Play Aware OS PCI IDE Bus Master PCI VGA Palette SnoopAllocate IRQ to PCI VGA Off-board PCI IDE Card Off-board PCI IDE Secondary IRQ DMA Channel Reserved Memory Address Peripheral SetupReserved Memory Size PCI Device Search Order Parallel Port Mode Serial Port2 ModeInfra-Red Transmission Mode Onboard Serial Port1 EPP Version CPU Current TemperatureCPU Overheat Warning Temperature Parallel Port IRQ CPU Fan Secondary Fan Change User PasswordAuto Detect Hard Disk Onboard IDE Change Supervisor Password Exit without Saving Auto Configuration with Fail-Safe SettingsSave Settings and Exit Upgrading the Microprocessor Chapter UpgradingUpgrading the System Memory Users Notes System Memory BiosAppendix a Embedded I/O Industrial Devices Miscellaneous Form Factor Control Panel ConnectionsCPU Socket PCB Construction Address Range Size Description Decimal Hexadecimal Memory MapDMA Channels Data Width System Resource Map Address hex Description Bus # Device # Function # Description PCI Configuration Space MapOn-board Devices PCI Interrupt Routing Map SignalInterrupts Connectors Pin-out Device Slave Address Pin# Serial Ports DB9M J36 and J37 Ethernet Header J31 Pin# Parallel DB25F J13 Pin# HDD LED Appendix B Flash Bios Programming Beeps Description Appendix C Disk-On-Chip Users Notes Software Reset Watchdog TimerHardware Reset Appendix D On-Board Industrial Devices Address Post Code Display Post Checkpoint Codes Checkpoint Description Code Table D-5 Bootblock Recovery Codes Table D-6 Uncompressed Initialization Codes Memory refresh line is toggling. Checking 3Ah Performing the DMA controller 2 base register test next Winbios Adaptor ROM had control and has now returned Table D-7 Bus Checkpoint Codes Bits Description Appendix E On-Board Ethernet Users Notes Page MN-RBXAT-03