Off-board PCI IDE Secondary IRQ, DMA Channel | Intel Raptor AT

Raptor AT – Installation Guide

Off-board PCI IDE Secondary IRQ

This option specifies the PCI interrupt used by the secondary IDE channel on the off-board PCI IDE controller. The settings are Disabled, INTA, INTB, INTC, INTD and Hardwired. The Optimal and Fail-Safe default setting is Disabled.

PCI Slot1 IRQ Priority

PCI Slot2 IRQ Priority

PCI Slot3 IRQ Priority

PCI Slot4 IRQ Priority

These options specify the IRQ priority for PCI devices installed in the PCI expansion slots. The settings are Auto, (IRQ) 3, 4, 5, 7, 9, 10, 11, 12 and 14. The Optimal and Fail-Safe default setting is Auto.

DMA Channel 0

DMA Channel 1

DMA Channel 3

DMA Channel 5

DMA Channel 6

DMA Channel 7

These options allow you to specify the bus type used by each DMA channel. The setting is either PNP or ISA/EISA. The optimal and fail-safe default setting is PNP.

IRQ3

IRQ4

IRQ5

IRQ7

IRQ9

IRQ10

IRQ11

IRQ12

IRQ14

IRQ15

These options specify the bus that the specified IRQ line is used on. These options allow you to reserve IRQs for legacy ISA adapter cards. These options determine if AMIBIOS should remove an IRQ from the pool of available IRQs passed to

30

Image 40

Intel Raptor AT manual Off-board PCI IDE Secondary IRQ, DMA Channel

Contents

Raptor AT Page Pre-Configuration Chapter Appendix a Technical Specifications Appendix B Flash Bios Programming Appendix C Disk-On-Chip Appendix D On-Board Industrial Appendix E On-Board Raptor AT Installation Guide System Board Pre-Configuration Introduction Static Electricity Warning CPU Support Supported Bus ClocksMemory On-Board I/O Conventions Used in this Manual On-Board Ethernet Pre-Configuration Static Warning Raptor AT Installation Guide Jumper Types Jumper Locations Jumper Locations Cmos Reset Reset Cmos Normal Clear CmosFlash Bios Write Protect Flash Write-protect Enabled Disabled Watchdog Timer Selection TimeoutClock Speed Selection Clock JP11 ATX Power Supply Enhancements Ethernet Selection Enabled DisabledAddress 110h Closed Open 310h Raptor AT Memory Configuration CPU Installation Designing for thermal performance Fan Heatsink Disk-on-Chip installation Installing Cables Power and Control Panel CablesInstalling Peripheral Cables Airflow management Pre-Configuration Location of Components and Connectors Index of Connectors Connector Description Users Notes Setup Starting Bios SetupUsing the Keyboard with Bios Setup Bios Setup Main Menu Date/Time Standard SetupFloppy Drive A, B Advanced Cmos Setup Boot Sector Virus ProtectionQuick Boot Pri Master Pri Slave Sec Master Sec Slave Try Other Boot Devices Initial Display ModeFloppy Access Control Hard Disk Access Control Boot Up Num Lock A.R.T. for Hard DisksFloppy Drive Swap Floppy Drive Seek Password Check Boot to OS/2Wait for F1 If Error Primary Display Advanced Chipset Setup System Bios CacheableInternal Cache C000,16K Shadow C400,16K Shadow BX/GX Master Latency Timer Clks Multi-Trans Timer ClksPCI 1 to PCI 0 Access USB KB/Mouse Legacy Support Aperture Access Global Enable PCI 0 Agent to Aperture Access Memory Autosizing SupportDram Integrity Mode Sdram RAS# to CAS# Delay Power Down Sdram Search for MDA Resources Bit I/O Recovery Time16bit I/O Recovery Time Sdram Precharge Control Power Management Setup Power Management/APM Power button FunctionGreen PC Monitor Power State Video Power Down Mode Power Saving Type Standby / Suspend Timer UnitStandby Timeout Suspend Timeout PCI/Plug and Play Setup PCI Latency Timer PCI ClocksLAN Wake-Up Plug and Play Aware OS PCI VGA Palette Snoop Allocate IRQ to PCI VGAPCI IDE Bus Master Off-board PCI IDE Card Off-board PCI IDE Secondary IRQ DMA Channel Peripheral Setup Reserved Memory SizeReserved Memory Address PCI Device Search Order Serial Port2 Mode Infra-Red Transmission ModeParallel Port Mode Onboard Serial Port1 CPU Current Temperature CPU Overheat Warning TemperatureEPP Version Parallel Port IRQ Change User Password Auto Detect Hard DiskCPU Fan Secondary Fan Onboard IDE Change Supervisor Password Save Settings and Exit Auto Configuration with Fail-Safe SettingsExit without Saving Upgrading the System Memory Chapter UpgradingUpgrading the Microprocessor Users Notes Appendix a BiosSystem Memory Embedded I/O Industrial Devices Miscellaneous Control Panel Connections CPU SocketForm Factor PCB Construction Memory Map DMA ChannelsAddress Range Size Description Decimal Hexadecimal Data Width System Resource Map Address hex Description On-board Devices PCI Configuration Space MapBus # Device # Function # Description Interrupts SignalPCI Interrupt Routing Map Connectors Pin-out Device Slave Address Pin# Serial Ports DB9M J36 and J37 Ethernet Header J31 Pin# Parallel DB25F J13 Pin# HDD LED Appendix B Flash Bios Programming Beeps Description Appendix C Disk-On-Chip Users Notes Watchdog Timer Hardware ResetSoftware Reset Appendix D On-Board Industrial Devices Address Post Code Display Post Checkpoint Codes Checkpoint Description Code Table D-5 Bootblock Recovery Codes Table D-6 Uncompressed Initialization Codes Memory refresh line is toggling. Checking 3Ah Performing the DMA controller 2 base register test next Winbios Adaptor ROM had control and has now returned Table D-7 Bus Checkpoint Codes Bits Description Appendix E On-Board Ethernet Users Notes Page MN-RBXAT-03