EPP Version, Parallel Port IRQ | Intel Raptor AT specs

Chapter 2:BIOS Configuration

EPP Version

1.7 and 1.9 (default) (available only for EPP mode).

Parallel Port IRQ

This option specifies the IRQ always used by the parallel port. When the port is set to a fixed address the settings are (IRQ) 5 and (IRQ) 7 (default), otherwise it is set to Auto.

Parallel Port DMA Channel

This option is only available if the setting for the Parallel Port Mode option is ECP. This option sets the DMA channel used by the parallel port. When the port is set to a fixed address the settings are DMA Channel 0, 1 and 3 (default), otherwise it is set to Auto.

CPU Current Temperature

The current CPU temperature is shown (only available with the optional hardware monitor).

CPU Overheat Warning

The setting is either Enabled or Disabled (default) (only available with the optional hardware monitor).

CPU Overheat Warning Temperature

Sets the CPU Overheat Warning Temperature set point (only available with the optional hardware monitor).

HW Monitor IN0 (CPU)

HW Monitor IN2 (+3.3V)

HW Monitor IN3 (+5V)

HW Monitor IN4 (+12V)

HW Monitor IN5 (-12V)

HW Monitor IN6 (-5V)

33

Image 43

Intel Raptor AT EPP Version, Parallel Port IRQ, Parallel Port DMA Channel, CPU Current Temperature, CPU Overheat Warning

Contents

Raptor AT Page Chapter Pre-Configuration Appendix B Flash Bios Programming Appendix C Disk-On-Chip Appendix a Technical Specifications Appendix E On-Board Appendix D On-Board Industrial Raptor AT Installation Guide Introduction System Board Pre-Configuration Static Electricity Warning On-Board I/O CPU SupportSupported Bus Clocks Memory On-Board Ethernet Conventions Used in this Manual Static Warning Pre-Configuration Raptor AT Installation Guide Jumper Types Jumper Locations Jumper Locations Flash Write-protect Enabled Disabled Cmos ResetReset Cmos Normal Clear Cmos Flash Bios Write Protect Clock JP11 Watchdog Timer SelectionTimeout Clock Speed Selection ATX Power Supply Enhancements Ethernet Selection Enabled DisabledAddress 110h Closed Open 310h CPU Installation Raptor AT Memory Configuration Fan Heatsink Designing for thermal performance Airflow management Disk-on-Chip installationInstalling Cables Power and Control Panel Cables Installing Peripheral Cables Pre-Configuration Location of Components and Connectors Connector Description Index of Connectors Users Notes Bios Setup Main Menu SetupStarting Bios Setup Using the Keyboard with Bios Setup Date/Time Standard SetupFloppy Drive A, B Pri Master Pri Slave Sec Master Sec Slave Advanced Cmos SetupBoot Sector Virus Protection Quick Boot Hard Disk Access Control Try Other Boot DevicesInitial Display Mode Floppy Access Control Floppy Drive Seek Boot Up Num LockA.R.T. for Hard Disks Floppy Drive Swap Primary Display Password CheckBoot to OS/2 Wait for F1 If Error C000,16K Shadow C400,16K Shadow Advanced Chipset SetupSystem Bios Cacheable Internal Cache USB KB/Mouse Legacy Support BX/GX Master Latency Timer ClksMulti-Trans Timer Clks PCI 1 to PCI 0 Access Sdram RAS# to CAS# Delay Aperture Access Global EnablePCI 0 Agent to Aperture Access Memory Autosizing Support Dram Integrity Mode Sdram Precharge Control Power Down SdramSearch for MDA Resources Bit I/O Recovery Time 16bit I/O Recovery Time Power Management Setup Video Power Down Mode Power Management/APMPower button Function Green PC Monitor Power State Suspend Timeout Power Saving TypeStandby / Suspend Timer Unit Standby Timeout Plug and Play Aware OS PCI/Plug and Play SetupPCI Latency Timer PCI Clocks LAN Wake-Up Off-board PCI IDE Card PCI VGA Palette SnoopAllocate IRQ to PCI VGA PCI IDE Bus Master DMA Channel Off-board PCI IDE Secondary IRQ PCI Device Search Order Peripheral SetupReserved Memory Size Reserved Memory Address Onboard Serial Port1 Serial Port2 ModeInfra-Red Transmission Mode Parallel Port Mode Parallel Port IRQ CPU Current TemperatureCPU Overheat Warning Temperature EPP Version Onboard IDE Change User PasswordAuto Detect Hard Disk CPU Fan Secondary Fan Change Supervisor Password Save Settings and Exit Auto Configuration with Fail-Safe SettingsExit without Saving Upgrading the System Memory Chapter UpgradingUpgrading the Microprocessor Users Notes Appendix a BiosSystem Memory Embedded I/O Miscellaneous Industrial Devices PCB Construction Control Panel ConnectionsCPU Socket Form Factor Data Width System Resource Memory MapDMA Channels Address Range Size Description Decimal Hexadecimal Address hex Description Map On-board Devices PCI Configuration Space MapBus # Device # Function # Description Interrupts SignalPCI Interrupt Routing Map Device Slave Address Connectors Pin-out Ethernet Header J31 Pin# Serial Ports DB9M J36 and J37 Pin# Pin# Parallel DB25F J13 HDD LED Appendix B Flash Bios Programming Beeps Description Appendix C Disk-On-Chip Users Notes Appendix D On-Board Industrial Devices Watchdog TimerHardware Reset Software Reset Post Code Display Address Checkpoint Description Code Post Checkpoint Codes Table D-5 Bootblock Recovery Codes Table D-6 Uncompressed Initialization Codes Memory refresh line is toggling. Checking 3Ah Performing the DMA controller 2 base register test next Winbios Adaptor ROM had control and has now returned Table D-7 Bus Checkpoint Codes Bits Description Appendix E On-Board Ethernet Users Notes Page MN-RBXAT-03