JVC VR-510U manual

LLT0010-001A

R

DIGITAL VIDEO RECORDER

VR-510U INSTRUCTIONS

For Customer Use:

Enter below the Serial No. which is

located on the rear of cabinet. Retain this

information for future reference.

Model No. VR-510U

Serial No.

POWER

WARNING

SLEEP REC STOP PLAY STILL

TIMER CANCEL

DISPLAY

REV FWD

EXECUTE

SKIP/ALARM

REC

CLOCK RESET/ CLEAR

OPE. LOCK

DIGITALVIDEORECORDER VR-510U

Contents

Main R DIGITAL VIDEO RECORDER VR-510U Page SAFETY PRECAUTIONS CAUTION ATTENTION INFORMATION CAUTION NOTE: Thank you for purchasing the JVC VR-510U digital video recorder. CONTENTS 1. INTRODUCTIONS 2. CONTROLS, CONNECTIONS AND DISPLAY 3. CONNECTIONS 1 INTRODUCTION Major features Large-capacity hard disk (80 GB) RS-232C control Simultaneous recording/playback mode 2 CONTROLS, CONNECTIONS AND DISPLAY 2-1 Front panel 1 1920 14 15161718 2-2 Rear panel 2 CONTROLS, CONNECTIONS AND DISPLAY (contd.) 2-3 Display 3 CONNECTIONS 3-1 Recording video signals from a camera Connecting a camera 3 CONNECTIONS (contd.) 3-2 Connecting more than one camera (using an external switcher) Connection procedures 3 CONNECTIONS (contd.) 3-3 Connecting signal input/output terminals [CAM SW OUT] camera switching signal output terminal [ALARM RESET] alarm signal reset input terminal [CLOCK RESET IN] clock reset input terminal [EXT REC IN] external recording control signal input terminal 4 PREPARATION 4-1 Installing a battery 4-2 Power supply 2. 3. 4-3 Setting the date and time 4 PREPARATION (contd.) 3. 4-4 Daylight-saving compensation During daylight-saving time Standard time 5 ON-SCREEN DISPLAY/MENU SWITCHES 5-1 On-screen display Preparation To change the position of the on-screen display To select the contents of the on-screen display 5-2 Menu switches Main menu screen Menu flow Jog/shuttle dial operation Shuttle dial operation Jog dial operation Display Connect the [MONITOR OUT] connector to the monitors video input connector. Setting Connect the [MONITOR OUT] connector to the monitors video input connector. 3. 5. 6. Set <REC QUALITY> and <REC SPEED> on the display panel. 5-3 Menu switch details The setting in [ ] is the factory setting. Page 5-3 Menu switch details Operation 6 RECORDING 6-1 Basic operation Major menu switches Recording system 6-2 Program timer recording Weekly timer 5. 6. Timer-recording for 24 hours or more ** **** *** ** ** 8. 9. Daily timer 11. 6 RECORDING (contd.) Canceling a timer recording program Changing timer program settings Operation in the Timer Recording Standby mode Estimated recording duration 6-3 Holiday timer recording 5. 6-4 Alarm recording Repeat recording during alarm recording 6-5 Sensor recording Pre-sensor recording 6-6 Recording with an external activation signal Connection Operation 6-7 Automatic restart of recording after power failure 7 PLAYBACK AND SPECIAL-EFFECTS PLAYBACK 7-1 Basic operation Operation Playback Simultaneous Playback mode 7-2 Jog/shuttle playback Shuttle playback operation Jog playback operation 7-3 Skip search Time search About the time search 7-3 Skip search Event search Alarm search About event/alarm search 7-4 Alarm or day/time direct search Alarm direct search Clearing the alarm list Day/time direct search 8 HARD DISK CONTROL 8-1 Hard disk maintenance Scan the disk when the power is ON. Scan the disk manually. Scanning the disk 8-1 Hard disk maintenance 8 HARD DISK CONTROL (contd.) Erasing & formatting Erasing & formatting 9 TROUBLESHOOTING 9-1 Error indication 9-2 No error indication 9 TROUBLESHOOTING (contd.) 9-pin connector specifications 10 RS-232C INTERFACE bit bit 10-1 Specifications 7 6 10-2 Protocols and commands 10 RS-232C INTERFACE (contd) JVC table 1 3A OA TXD RXD 10-3 Commands 2-bit 1-bit 0-bit Playback camera 1 0 0 Fixed Command Description Page Page 11 OTHERS 11-1 Recording time AUDIO REC OFF (80 GB) AUDIO REC ON (160 GB) AUDIO REC OFF (160 GB) 11-2 Signal input/output terminals 11 OTHER (contd.) 11-3 Specifications 11 OTHER (contd.) <General> <Video signal system> <Audio signal system>