8 HARD DISK CONTROL
8-1 Hard disk maintenance
When power is interrupted (disconnection, power failure, etc.) in the Record mode or Sensor Record Standby mode, the recording information on the hard disk may be damaged. This may cause problems in recording and playback.
To repair the hard disk, two disk scan functions (<AUTO SCANDISK> and <MANUAL SCAN DISK>) are available.
●<AUTO SCANDISK>
If <AUTO SCANDISK> is set to “ON”, the disk is scanned automatically whenever the power is turned on or restored. To cancel disk scanning, press the [CLOCK RESET/CLEAR] button.
●<MANUAL SCAN DISK>
Execute <MANUAL SCAN DISK> from the menu. This cannot be canceled once it has been started. Do not turn the power OFF while this operation is in progress. When <AUTO SCANDISK> is set to “OFF” and the power is kept turned on for long- time recording, be sure to execute <MANUAL SCAN DISK> regularly.
It is recommended to perform <MANUAL SCAN DISK> once a month if recording is executed continuously.
|
| Scanning the disk |
| |
|
| Jog dial |
|
|
[MENU] button | Shuttle search dial |
| ||
|
| DIGITAL VIDEO RECORDER |
| |
CANCEL | MENU | L |
|
|
SE ECT |
|
| ||
| REV | FWD | REC |
|
|
|
| ||
DISPLAY | SEARCH |
| CLOCK RESET/ CLEAR |
|
|
|
|
| [CLOCK |
PLAY | STILL | EXECUTE | OPE. LOCK | RESET/CLEAR] |
|
|
|
| |
|
| SKIP/ALARM | ON | button |
|
|
|
| |
|
| SEARCH |
|
|
[SKIP SEARCH·EXECUTE] button
Scan the disk when the power is ON.
1.Display the [UTILITY] screen.
Display the [UTILITY] screen in the main menu [SYSTEM/LIST]. For details, refer to “Setting” on page 18.
2.Set the menu switches.
Set the cursor to [AUTO SCAN DISK] with [JOG f] and set to “ON” with [JOG – +].
When the setting is complete, press the [MENU] button twice to restore the normal screen.
When the power is turned ON, the disk is scanned and the "SYSTEM LOADING **%" message is displayed. Scanning progress is indicated in percentage. When disk scanning is complete, the % indication goes out.
“LoAd
1.
2.
[ S Y ST E M ] | JOG | |
|
| [ 8 0 GB ] |
U T I L I T Y |
| |
[ L I S T ] |
| |
HOUR ME T E R |
| |
POWER LO S S | L I S T | |
[ U T I L I T Y ] | JOG + |
1 . A UT O S C A N D I S K | ON |
2 . MAN UA L S C A N D I S K | O F F |
3 . Q U I C K E R AS E | O F F |
C U R R E N T FO R MAT | S T D |
E X E C U T E : P R E S S | B U T T O N |
VN
S
Scan the disk manually.
1.Display the [UTILITY] screen.
Display the [UTILITY] screen in the main menu [SYSTEM/LIST]. For details, refer to “Setting” on page 18.
2.Set the menu switches.
Set the cursor to [MANUAL SCAN DISK] with [JOG f] and set to “ON” with [JOG – +].
“EXECUTE: PRESS £ BUTTON” is displayed on the monitor.
Reference:
3.Scan the disk.
Press the [SKIP SEARCH·EXECUTE] button to start scanning the disk.
“SCAN DISK **%” is shown on the monitor.
Caution:
●Disk scanning can take up to 3 hours if the hard disk contains a lot of data.
Memo:
●Even if <AUTO SCANDISK> is set to "OFF", "SYSTEM
LOADING**%" may be displayed when the power is turned ON.
36
