JVC VR-510U manual Rear panel

2 CONTROLS, CONNECTIONS AND DISPLAY (contd.)

2-2 Rear panel

26

CAMERA IN

1

12

MONITOR OUT

27				28
AUDIO			RS-232C
IN
1
CAM SW ALARM		SPARE		ALARM	CLOCK EXT
OUT	IN1			RESET RESET IN REC IN
2	SPARE				CLOCK	HDD
COM			SPARE COM RESET OUT			FULL OUT
AUDIO
OUT

21

POWER

ON I O OFF

SIGNAL GND	AC IN 120 V
	50 Hz / 60 Hz

25

24 23 22

&[STOP] button

Press this button to stop operation. In the Simultaneous Playback mode, press this button to stop playback and engage

*the normal recording mode.

[REC] button

Press in the Stop mode to start recording. The recording mode can be set with the menu switch.

(Reference: “6-1 Basic operation” on page 22.

[SLEEP] button

Before turning the power OFF, press this button to stop the )rotation of the hard disk.

[SYSTEM RESET] button

This button is used for servicing. Normally, you do not need to

quse this button.

[POWER] switch Turns power ON/OFF.

*Before turning the power OFF, press the ([SLEEP] button to wstop the rotation of the hard disk.

[AC IN] socket

eConnect to an AC 120 V outlet using the provided power cable.

Signal input/output terminal

CAM SW OUT

Outputs camera switch timing control signals when this unit is connected to a frame switcher.

Reference: "3-2 Connecting more than one camera (using an external switcher)" on page 10.

ALARM IN 1

Accepts signals to start alarm or sensor recording.

ALARM RESET

Accepts signals to stop recording during alarm or sensor recording.

CLOCK RESET IN

Connect to a master clock or the [CLOCK RESET OUT] terminal of another device. When a clock reset signal is input, this unit can be set to the master clock or the other device’s clock.

When the clock reset signal is input, the clock second value is reset: .

●With 29 seconds or less, the minute value stays the same and the second value is reset to 00.

●With 30 seconds or more, the minute value is increased by 1 and the second value is reset to 00.

CLOCK RESET OUT

Outputs a clock reset signal when the internal clock is 00:00 or 12:00.

EXT REC IN

Recording is automatically activated by an external signal when menu switch <REC MODE> of <EXT MODE> is set to “TRIG” or “MANUAL”.

Reference: “5-3 Menu switch details” on page 20.

HDD FULL OUT

Outputs a signal during recording when the hard disk’s available space is 0% except in the following cases.

●Menu switch <HDD FULL OUT> set to “OFF”

●Menu switch <REPEAT REC> set to “ALL”

Reference: “5-3 Menu switch details” on page 20.

r[AUDIO OUT] audio output connector Outputs recorded audio during playback.

In the Record or Stop mode, outputs the input audio signal. Audio is not output in the following cases.

●When playing back signals recorded with menu switch <REC SPEED> set to “1/5” or “1/10”

●In the Frame-by-Frame Playback, Still or Search mode

●When playing back signals recorded with menu switch <AUDIO REC> set to “OFF”

t● When the menu is displayed

[MONITOR OUT] monitor output connector

Outputs video signals recorded on the hard disk in the Play mode. In the Record mode, outputs video input signals from the camera or frame switcher connected to the [CAMERA IN] connector.

The picture signal from the [CAMERA IN] connector is output through the [MONITOR OUT] connector even when the power is

yturned OFF.

[CAMERA IN] camera input connector uConnect to a camera.

[AUDIO IN] audio input connector

Connect to the audio output connector of the audio source

idevice.

[RS-232C] remote connector

Connect a personal computer or compatible control unit for external remote operation.

Reference: “10. RS-232C INTERFACE” on page 40.

7