Rear panel, Headphone connection | Kathrein 9986492, MSK 33 specification

Displays, Operating Elements and Connections

Rear panel

The interfaces, output and input sockets and the mains connection are located on the rear panel of the MSK 33.

1Mains connection

3Mains switch

5DC socket (Option / XLR-socket)

for the operation of an external DC voltage of 10.8...14 V and for charging the accumulator

7Headphone connection

3.5mm jack plug for stereo headphones

8TS parallel Option

10AUX 1

unoccupied or BNC socket for video output

2 Mains fuse

4 Loudspeaker

6 Scart socket

Interface RS 232 / modem

For modems for remotely controlling the MSK 33 and for the software download

9 Ventilators

11AUX 2 unoccupied

17

Image 17

Kathrein 9986492, MSK 33 Rear panel, Mains connection Mains switch DC socket Option / XLR-socket, Headphone connection

Contents

Sat/TV/FM Test Receiver MSK Page Preface Contents Checking the LNB supply voltage of a satellite receiver Selecting the colour standards PAL, Secam and Ntsc Mpeg transport stream interface TS-Parallel, Lvds optional Measuring an audio signal via the AV socket Scart Measurement of analogue signals in Sat operation 100 113 107 Explanation of symbols General safety informationImportant Notes Validity of this manual Connections Safety InstructionsProper use Mechanical loadbearing capacity Functions Functions Function Functions overviewReturn path LP DVB-S DVB-S/C/T Front panel Displays, Operating Elements and Connections Rear panel Mains connection Mains switch DC socket Option / XLR-socketHeadphone connection TS parallel Option 10 AUX Side view MSK Observing angle of the on screen display Frequently recurring softkeys Operating ConceptScreen Menu selection General information for operationMain menu Accu CAP % I=0.00 a Mains voltage / mains switch Place of installation of the MSKOn/Off switch Safety fuse DC socket option Accumulator and Battery OperationAccumulator operation Connections Maximal input level Measurement PossibilitiesLevel measurement Sat menu Sat Operation Entering the transponder frequency Setting of the LNB voltage supplySelecting the LO frequency Bargraph Level range Comment Display Switch-over of Analog digit. DvbsIII Calling up menu LNB-CONTROL LNB control menu KHz control signalLNB supply voltage LNB current draw DiSEqC Checking the LNB supply voltage of a satellite receiverCalling up the DiSEqC/V SEC menu DiSEqC menu TX display field Submenu for entering DiSEqC commandsDisplay field a Display field B Data burst Tone burst Example Entering and transmitting a DiSEqC commandSimple DiSEqC General information UFOmicro DiSEqC menuDisplay fields RX 0 E2 10 1390 Tx+rx CommandOperating the menus Modus Sat Operation Entering the hex numbers Sending a V-SEC command TXSEC menu Initial ANALOG-menu Level-dependent acoustic signalCalling up the sound subcarrier Menu Video polarity Second Anlaog menu Setting of the de-emphasis Audio carrier settingSat subcarrier menu Audio carrier frequency Audio carrier table for reception type Audio carrier tables for the satellite reception 27.500 Digital MeasurementsSAT Digital menu Level measurement Digital Min./Max. levels TV menu TV OperationC10 210.25MHz A65.0dBµV Rf chan LNB U= 0.0 V I= 0 mA TV control menuTV-DiSEqC /VSEC menu Selecting the standard Analogue menuAudio carrier table for TV reception Selecting the audio carriers Measuring the current level Measuring the min./max. levelSelecting the colour standards PAL, Secam and Ntsc Measuring audio carrier spacing Selecting demodulation for DVB-C measurement TV Digital menuMode 900 SR1 ChBW 8MHz DVB-T optionalSelecting channel bandwidths Return path if menu Return Path if Menu Audio carrier table for if reception Analog menu Measurement of the current level Measurement of the min./max. levelMeasurement of the audio carrier spacing If RP Digital Menu QAM64 modeEntering symbol rate Radio Analog menu Radio OperationRadio menu Measuring the min/max level FM Measure ALL Decoder operation AV MenuDecoder operation baseband Video input Video output Mpeg transport stream interface TS-Parallel, Lvds optional Breaking voltageRGB operation 3sat KiKa Phoenix Mpeg Decoder Menu OptionalPAT 08 Offset 0.0 dB Setting MenuUnit dBmV Screen Menu Screen setup Setting the time Click button Setting the dateSystem Menu Calls up the SYS TEM menu Saving the unit settings Saving and calling up unit settingsCalling up saved settings Copy Menu Printing out all measurements in Sat mode Printing out all measurements in TV mode Spectr Mode Menu Enlarging the videotext Text MenuHolding the videotext Original videotext size Horizontal zoom -Enlarging the video signal Horizontal zoom Reducing the video signalScope Menu Video scope menu Selecting the video line Measurement of the amplitude of the video signalMeasurement of video signals via the AV socket Scart Pos Audio ScopeTime DiSEqC Scope Position and triggering of the DiSEqC signalSaving function Shot Cont Marker Span Large ¡ mark ßlevel Spectral MenuAna Max Marker Dig Marker Ana Zoom marker Max off Measurement of digital signals in Sat operationCross-polarisation measurement on signals in SAT operation Measurement of the bit error rate BER Constellation diagram for Qpsk DVB-SConst Menu Colour representation of I/Q value pairs Frontend locked Measurement of signal noise ratio SNRCarrier offset Inverting /not inverting a constellation diagram Selecting the symbol rate symbol-clock27.500 SR Selecting the code rate Examples for Qpsk constellation diagrams Measurement of modulation error rate MER Constellation diagram for QAM DVB-C Zoom Inverting /not inverting constellation diagram Examples for QAM constellation diagram Const Menu Measurement of bit error rate BER Constellation diagram DVB-T optionalMeasurement of signal noise ration SNR Carrier mode Hierarchy Code rate Guard Invers Frontend locked Channel display Impulse response representation Echo representation optional Measuring principle Broadband Cable Analysis Measuring System MSK Track MVG10 Downstream measurement Upstream measurementMSK33 MVG10 RGB MSK33 Cable system With return path capable amplifiers Display of the check point Auto Measure Connection cable for modem / RS InterfacesModem / RS 232 interface Setting local echo Setting baud rateSetting hardware handshake Modem/RS232 menu TTY mode Code PasswordAnsi mode Log-in procedure Requesting help Example for logging-in in Ansi mode Interfaces List of the command abbreviations STU Loading and saving predefined settingsSTU RET LDU Maintenance, Storage and Customer Service Ribbon exchange Printer paper-exchanging the ribbonBefore opening the unit, disconnect the supply voltage Command overview framing byte Overview of DiSEqC commandsCommand overview address byte Technical Appendix Reset Reset DiSEqC minicontroller Command overview command byte Command overview data byte DiSEqC commands for Kathrein matricesCommand for Kathrein matrix 9xx-series Command for Kathrein matrix EXR Channel and frequency table standard B/G frequency in MHz Channel tablesVHF-CCIR UHF-CCIR USB/OSB ESB VHF UHF Channel and frequency table standard Lfrequency in MHz VII Channel and frequency table standard D/K frequency in MHzViii XII Channel and frequency table standard I frequency in MHz Channel and frequency table standard M/N frequency in MHz Channel and frequency table standard M/Nfrequency in MHz Power supply Technical DataTechnical data MER SNRQpsk BER Assignment of the Scart socket AccessoriesScope of delivery TXD RXD RTS CTS DSR GND DCD DTR Assignment of RS232 socket Assignment of socket TS Parallel optional Unit variants General notes Downloading New MSK33 Operating Software 114 115