27.500 SR, Selecting the symbol rate symbol-clock | Kathrein MSK 33

Const Menu

27.500 SR 1 ►

3/4 CR ►

Invers (no)

Mode

QPSK

Selecting the symbol rate (symbol-clock)

27.5 MS, 20 MS, 24.5 MS or 22 MS – or entry between 0.5…32 MS.

Selecting the code rate

(1/2, 2/3, 3/4, 4/5, 5/6, 6/7, 7/8, 8/9)

Inverting /not inverting a constellation diagram

Display the status of the frequency spectrums or the constellation diagram. Setting automatically occurs.

No function.

74

Image 74

Kathrein MSK 33, 9986492 manual 27.500 SR, Selecting the symbol rate symbol-clock, Selecting the code rate

Contents

Sat/TV/FM Test Receiver MSK Page Preface Contents Checking the LNB supply voltage of a satellite receiver Selecting the colour standards PAL, Secam and Ntsc Mpeg transport stream interface TS-Parallel, Lvds optional Measuring an audio signal via the AV socket Scart Measurement of analogue signals in Sat operation 100 107 113 Important Notes General safety informationExplanation of symbols Validity of this manual Proper use Safety InstructionsConnections Mechanical loadbearing capacity Functions Functions Return path LP Functions overviewFunction DVB-S DVB-S/C/T Displays, Operating Elements and Connections Front panel Headphone connection Mains connection Mains switch DC socket Option / XLR-socketRear panel TS parallel Option 10 AUX Observing angle of the on screen display Side view MSK Frequently recurring softkeys Operating ConceptScreen Main menu General information for operationMenu selection Accu CAP % I=0.00 a On/Off switch Place of installation of the MSKMains voltage / mains switch Safety fuse DC socket option Accumulator and Battery OperationAccumulator operation Connections Maximal input level Measurement PossibilitiesLevel measurement Sat Operation Sat menu Entering the transponder frequency Setting of the LNB voltage supplySelecting the LO frequency III Switch-over of Analog digit. DvbsBargraph Level range Comment Display Calling up menu LNB-CONTROL LNB supply voltage KHz control signalLNB control menu LNB current draw DiSEqC Checking the LNB supply voltage of a satellite receiverCalling up the DiSEqC/V SEC menu DiSEqC menu Display field a Submenu for entering DiSEqC commandsTX display field Display field B Data burst Tone burst Example Entering and transmitting a DiSEqC commandSimple DiSEqC Display fields UFOmicro DiSEqC menuGeneral information RX 0 E2 10 Operating the menus Tx+rx Command1390 Modus Sat Operation Entering the hex numbers Sending a V-SEC command TXSEC menu Calling up the sound subcarrier Level-dependent acoustic signalInitial ANALOG-menu Menu Second Anlaog menu Video polarity Sat subcarrier menu Audio carrier settingSetting of the de-emphasis Audio carrier frequency Audio carrier tables for the satellite reception Audio carrier table for reception type 27.500 Digital MeasurementsSAT Digital menu Level measurement Digital Min./Max. levels C10 210.25MHz A65.0dBµV TV OperationTV menu Rf chan LNB U= 0.0 V I= 0 mA TV control menuTV-DiSEqC /VSEC menu Audio carrier table for TV reception Analogue menuSelecting the standard Selecting the audio carriers Selecting the colour standards PAL, Secam and Ntsc Measuring the min./max. levelMeasuring the current level Measuring audio carrier spacing Mode TV Digital menuSelecting demodulation for DVB-C measurement 900 SR1 ChBW 8MHz DVB-T optionalSelecting channel bandwidths Return Path if Menu Return path if menu Analog menu Audio carrier table for if reception Measurement of the current level Measurement of the min./max. levelMeasurement of the audio carrier spacing If RP Digital Menu QAM64 modeEntering symbol rate Radio Analog menu Radio OperationRadio menu FM Measure ALL Measuring the min/max level Decoder operation baseband Video input AV MenuDecoder operation Video output Mpeg transport stream interface TS-Parallel, Lvds optional Breaking voltageRGB operation 3sat KiKa Phoenix Mpeg Decoder Menu OptionalPAT 08 Offset 0.0 dB Setting MenuUnit dBmV Screen setup Screen Menu System Menu Setting the dateSetting the time Click button Calls up the SYS TEM menu Calling up saved settings Saving and calling up unit settingsSaving the unit settings Copy Menu Printing out all measurements in TV mode Printing out all measurements in Sat mode Mode Menu Spectr Holding the videotext Text MenuEnlarging the videotext Original videotext size Scope Menu Horizontal zoom Reducing the video signalHorizontal zoom -Enlarging the video signal Video scope menu Selecting the video line Measurement of the amplitude of the video signalMeasurement of video signals via the AV socket Scart Pos Audio ScopeTime Saving function Position and triggering of the DiSEqC signalDiSEqC Scope Shot Cont Ana Spectral MenuMarker Span Large ¡ mark ßlevel Max Marker Ana Marker Dig Zoom marker Max off Measurement of digital signals in Sat operationCross-polarisation measurement on signals in SAT operation Const Menu Constellation diagram for Qpsk DVB-SMeasurement of the bit error rate BER Colour representation of I/Q value pairs Frontend locked Measurement of signal noise ratio SNRCarrier offset 27.500 SR Selecting the symbol rate symbol-clockInverting /not inverting a constellation diagram Selecting the code rate Examples for Qpsk constellation diagrams Constellation diagram for QAM DVB-C Measurement of modulation error rate MER Inverting /not inverting constellation diagram Zoom Examples for QAM constellation diagram Const Menu Measurement of signal noise ration SNR Constellation diagram DVB-T optionalMeasurement of bit error rate BER Carrier mode Hierarchy Code rate Guard Invers Frontend locked Channel display Impulse response representation Echo representation optional Broadband Cable Analysis Measuring System MSK Measuring principle Track MVG10 MSK33 MVG10 Upstream measurementDownstream measurement RGB MSK33 Cable system With return path capable amplifiers Auto Measure Display of the check point Connection cable for modem / RS InterfacesModem / RS 232 interface Setting hardware handshake Setting baud rateSetting local echo Modem/RS232 menu Ansi mode Code PasswordTTY mode Log-in procedure Example for logging-in in Ansi mode Requesting help Interfaces List of the command abbreviations STU RET Loading and saving predefined settingsSTU LDU Maintenance, Storage and Customer Service Ribbon exchange Printer paper-exchanging the ribbonBefore opening the unit, disconnect the supply voltage Command overview address byte Overview of DiSEqC commandsCommand overview framing byte Technical Appendix Command overview command byte Reset Reset DiSEqC minicontroller Command for Kathrein matrix 9xx-series DiSEqC commands for Kathrein matricesCommand overview data byte Command for Kathrein matrix EXR VHF-CCIR UHF-CCIR Channel tablesChannel and frequency table standard B/G frequency in MHz USB/OSB ESB Channel and frequency table standard Lfrequency in MHz VHF UHF Viii Channel and frequency table standard D/K frequency in MHzVII XII Channel and frequency table standard I frequency in MHz Channel and frequency table standard M/N frequency in MHz Channel and frequency table standard M/Nfrequency in MHz Power supply Technical DataTechnical data MER SNRQpsk BER Assignment of the Scart socket AccessoriesScope of delivery Assignment of RS232 socket TXD RXD RTS CTS DSR GND DCD DTR Assignment of socket TS Parallel optional Unit variants Downloading New MSK33 Operating Software General notes 114 115