Hierarchy | Kathrein 9986492, MSK 33 instruction

DVB-T

Hierarchy

Meaning: Two carriers streams are simultaneously transmitted and the transport stream with the higher priority is QPSK modulated.

There are four hierarchy steps (0, 1, 2 and 4).

Hierarchy = 0 menus, that the signal is not hierarchy modulated.

Hierarchy = 1 means, that the signal is hierarchically modulated. Two transport streams are simultaneously transmitted, one has higher priority in QPSK.

Hierarchy = 2 menus, that the signal is hierarchically modulated. The modulation is compared to the QAM modulation is one step securer.

Hierarchy = 4 means, that the signal is hierarchically modulated. the QPSK modulation is securer that the QAM modulation by two steps.

81

Image 81

Kathrein 9986492, MSK 33 manual Hierarchy

Contents

Sat/TV/FM Test Receiver MSK Page Preface Contents Checking the LNB supply voltage of a satellite receiver Selecting the colour standards PAL, Secam and Ntsc Mpeg transport stream interface TS-Parallel, Lvds optional Measuring an audio signal via the AV socket Scart Measurement of analogue signals in Sat operation 100 113 107 Explanation of symbols General safety informationImportant Notes Validity of this manual Connections Safety InstructionsProper use Mechanical loadbearing capacity Functions Functions Function Functions overviewReturn path LP DVB-S DVB-S/C/T Front panel Displays, Operating Elements and Connections Rear panel Mains connection Mains switch DC socket Option / XLR-socketHeadphone connection TS parallel Option 10 AUX Side view MSK Observing angle of the on screen display Operating Concept ScreenFrequently recurring softkeys Menu selection General information for operationMain menu Accu CAP % I=0.00 a Mains voltage / mains switch Place of installation of the MSKOn/Off switch Safety fuse Accumulator and Battery Operation Accumulator operationDC socket option Connections Measurement Possibilities Level measurementMaximal input level Sat menu Sat Operation Setting of the LNB voltage supply Selecting the LO frequencyEntering the transponder frequency Bargraph Level range Comment Display Switch-over of Analog digit. DvbsIII Calling up menu LNB-CONTROL LNB control menu KHz control signalLNB supply voltage LNB current draw Checking the LNB supply voltage of a satellite receiver Calling up the DiSEqC/V SEC menuDiSEqC DiSEqC menu TX display field Submenu for entering DiSEqC commandsDisplay field a Display field B Example Entering and transmitting a DiSEqC command Simple DiSEqCData burst Tone burst General information UFOmicro DiSEqC menuDisplay fields RX 0 E2 10 1390 Tx+rx CommandOperating the menus Modus Sat Operation Sending a V-SEC command TX SEC menuEntering the hex numbers Initial ANALOG-menu Level-dependent acoustic signalCalling up the sound subcarrier Menu Video polarity Second Anlaog menu Setting of the de-emphasis Audio carrier settingSat subcarrier menu Audio carrier frequency Audio carrier table for reception type Audio carrier tables for the satellite reception Digital Measurements SAT Digital menu27.500 Level measurement Digital Min./Max. levels TV menu TV OperationC10 210.25MHz A65.0dBµV Rf chan TV control menu TV-DiSEqC /VSEC menuLNB U= 0.0 V I= 0 mA Selecting the standard Analogue menuAudio carrier table for TV reception Selecting the audio carriers Measuring the current level Measuring the min./max. levelSelecting the colour standards PAL, Secam and Ntsc Measuring audio carrier spacing Selecting demodulation for DVB-C measurement TV Digital menuMode 900 SR1 DVB-T optional Selecting channel bandwidthsChBW 8MHz Return path if menu Return Path if Menu Audio carrier table for if reception Analog menu Measurement of the min./max. level Measurement of the audio carrier spacingMeasurement of the current level QAM64 mode Entering symbol rateIf RP Digital Menu Radio Operation Radio menuRadio Analog menu Measuring the min/max level FM Measure ALL Decoder operation AV MenuDecoder operation baseband Video input Video output Breaking voltage RGB operationMpeg transport stream interface TS-Parallel, Lvds optional Mpeg Decoder Menu Optional PAT 083sat KiKa Phoenix Setting Menu Unit dBmVOffset 0.0 dB Screen Menu Screen setup Setting the time Click button Setting the dateSystem Menu Calls up the SYS TEM menu Saving the unit settings Saving and calling up unit settingsCalling up saved settings Copy Menu Printing out all measurements in Sat mode Printing out all measurements in TV mode Spectr Mode Menu Enlarging the videotext Text MenuHolding the videotext Original videotext size Horizontal zoom -Enlarging the video signal Horizontal zoom Reducing the video signalScope Menu Video scope menu Measurement of the amplitude of the video signal Measurement of video signals via the AV socket ScartSelecting the video line Audio Scope TimePos DiSEqC Scope Position and triggering of the DiSEqC signalSaving function Shot Cont Marker Span Large ¡ mark ßlevel Spectral MenuAna Max Marker Dig Marker Ana Measurement of digital signals in Sat operation Cross-polarisation measurement on signals in SAT operationZoom marker Max off Measurement of the bit error rate BER Constellation diagram for Qpsk DVB-SConst Menu Colour representation of I/Q value pairs Measurement of signal noise ratio SNR Carrier offsetFrontend locked Inverting /not inverting a constellation diagram Selecting the symbol rate symbol-clock27.500 SR Selecting the code rate Examples for Qpsk constellation diagrams Measurement of modulation error rate MER Constellation diagram for QAM DVB-C Zoom Inverting /not inverting constellation diagram Examples for QAM constellation diagram Const Menu Measurement of bit error rate BER Constellation diagram DVB-T optionalMeasurement of signal noise ration SNR Carrier mode Hierarchy Code rate Guard Invers Frontend locked Channel display Impulse response representation Echo representation optional Measuring principle Broadband Cable Analysis Measuring System MSK Track MVG10 Downstream measurement Upstream measurementMSK33 MVG10 RGB MSK33 Cable system With return path capable amplifiers Display of the check point Auto Measure Interfaces Modem / RS 232 interfaceConnection cable for modem / RS Setting local echo Setting baud rateSetting hardware handshake Modem/RS232 menu TTY mode Code PasswordAnsi mode Log-in procedure Requesting help Example for logging-in in Ansi mode Interfaces List of the command abbreviations STU Loading and saving predefined settingsSTU RET LDU Maintenance, Storage and Customer Service Printer paper-exchanging the ribbon Before opening the unit, disconnect the supply voltageRibbon exchange Command overview framing byte Overview of DiSEqC commandsCommand overview address byte Technical Appendix Reset Reset DiSEqC minicontroller Command overview command byte Command overview data byte DiSEqC commands for Kathrein matricesCommand for Kathrein matrix 9xx-series Command for Kathrein matrix EXR Channel and frequency table standard B/G frequency in MHz Channel tablesVHF-CCIR UHF-CCIR USB/OSB ESB VHF UHF Channel and frequency table standard Lfrequency in MHz VII Channel and frequency table standard D/K frequency in MHzViii XII Channel and frequency table standard I frequency in MHz Channel and frequency table standard M/N frequency in MHz Channel and frequency table standard M/Nfrequency in MHz Technical Data Technical dataPower supply SNR Qpsk BERMER Accessories Scope of deliveryAssignment of the Scart socket TXD RXD RTS CTS DSR GND DCD DTR Assignment of RS232 socket Assignment of socket TS Parallel optional Unit variants General notes Downloading New MSK33 Operating Software 114 115