Kathrein 9986492, MSK 33 - page 62

Copy Menu

62

Printing the measurement results

By pressing the softkey, the current measurement result along with the date and

time are printed out.

Printing out a measurement result in TV mode with:

- Date and time

- Channel number, frequency

- Analogue measurement (A), level.

If the function, „measure,“ is called up in the TV, Sat or FM menu, all the meas-

urements are printed out.

Printing out all measurements in TV mode

The printout contains the following measurement results:

- Date and time

- Audio carrier spacing TT1: - 13 dB

- Audio carrier spacing TT2: not available

- Audio carrier spacing NICAM: - 20 dB

- Bit error rate NICAM: 8.20E -06

- Minimal level: 52.5 dBµV

- Maximal level: 59 dBµV

- Channel: 10

- Video carrier frequency: 210.25 MHz

- Analogue measurement: A

- Current level: 56 dBµV

Printing out all measurements in Sat mode

The printout contains the following measurement results:

- Minimal level: 67.5 dBµV

- Maximal level: 69 dBµV

- Transponder frequency: 11373,15 MHz

- Analogue measurement: A

- Current level: 68 dBµV

Line feed

Contents

Main Operating manual Sat/TV/FM Test Receiver MSK 33 Page Preface Page Page Page Page Page Page Page Page Important Notes * Validity of this manual General safety information Explanation of symbols Safety Instructions Connections Proper use Mechanical loadbearing capacity Functions Functions Functions Functions overview Front panel 2 10 12 Rear panel Observing angle of the on screen display MSK 33 front viel The angle of view from the side to the TFT display is + 45. Operating Concept The screen Frequently recurring softkeys Operating Concept General information for operation Menu selection The main menu Operation Place of installation of the MSK 33 Mains voltage / mains switch On/Off switch Safety fuse Accumulator and Battery Operation Accumulator operation DC socket (option) Connections RF output AV Headphone connection Modem / RS232 interface Measurement Possibilities Level measurement Maximal input level * Setting of the LNB voltage supply: Selecting the LO frequency Entering the transponder frequency: <>sat frq LNB CONTROL SAT MEASURE LNB: U= 14,0V I=181mA BACK off BACK analog SCAN LNB CONTROL digit. DVBS > SAT MEASURE analog > LNB control menu LNB current draw 22kHz 14.0V on > 18.0V off> 09750 Lo 1> DiSEqC VSEC LNB: U= 14,0V I=181mA BACK Page DiSEqC menu RX assessment input Transmitting and receiving a DiSEqC command (TX + RX) Sending a DiSEqC command (TX) Submenu for entering DiSEqC commands TX display field Display field A Display field B * Simple DiSEqC data burst tone burst tx UFOmicro DiSEqC menu General information RX 0 E2 10 33 ----- Display fields Page Installation of a UFO unit EXU 544 in conjunction with the MSK 33 Page Initial ANALOG-menu Calling up the sound subcarrier menu ><11208.00MHz A56.0dBV Level-dependent acoustic signal SUBCAR mea- sure MORE ---SAT MEASURE ALL--- min/max 55.5/56.0dbV level beep ------------- 70 Second ANLAOG menu Sat subcarrier menu Selecting the subcarrier recep- tion type Audio carrier frequency Audio carrier setting Setting of the de-emphasis Audio carrier tables for the satellite reception Digital Measurements SAT DIGITAL menu ><1832.50MHz D65.0 dBV MPEG Level-dependent acoustic signal Digital Measurements Level measurement DIGITAL (Min./Max. levels) TV menu Frequency entry of 44.75-867.2 MHz / DVB-T / BIII / UHF C10 210.25MHz A65.0dBV Mid-channel display Entering in a channel TV control menu 22 kHz control signal LNB: U = 14,6V I = 181mA LNB supply voltage Remote supply voltage Analogue menu Selecting the standard Audio carrier table for TV reception Selecting the audio carriers Level-dependent acoustic signal ----TV MEASURE ALL --- SC1/SC2:-13.5/-19.5dB NICAM: -18.5 dB BER : 5.6E-06 TV DIGITAL menu DVB-C S32 394.00MHz D65.0dBV Level-dependent acoustic signal beep QAM64 mode > DVB-T (optional) MPEG Level-dependent acoustic signal beep C21 474.00MHz D65.0dBV chBW 8 MHz > Return path IF menu Entering a frequency of 7.00 MHz up to 80.00MHz* RP 22.40 MHz A 65.0dBV TV-IF38.90MHz A65.0dBV Inverting the RF spectrum* ANALOG menu Carrying out measurements Measurement of the min./max. level Selecting the colour standards PAL, SECAM and NTSC ----TV MEASURE ALL --- SC1/SC2:-13.5/-19.5dB NICAM: -18.5 dB BER : 5.6E-06 IF RP DIGITAL Menu DVB-C MPEG RP 48.25MHz D65.0 dBV Level-dependent acoustic signal Radio Operation RADIO menu Entering a frequency from 44.75 MHz to 867.20 MHz RADIO CONTROL menu ANALOG menu Radio Operation Measuring the min/max level in/max: 61.5/64.5dBV Measuring the current level ----FM MEASURE ALL --- AV Menu Decoder operation Decoder operation baseband Video input Video output AV Menu Breaking voltage RGB operation MPEG transport stream interface (TS-Parallel, LVDS) (optional) Fb RGB off Fb RGB on MPEG Decoder Menu (Optional) show PAT manual V-PID manual A-PID Video-PID: 1040 MPEG 2V Audio-PID: 1042 MPEG 2A Norm: dig. television Status:running CA:no ---- PAT (08) --00-- >ZDF < 3sat KiKa Phoenix ORF ---- PAT (08) --00-- >ZDF < Setting Menu Modem menu Screen menu SYSTEM menu Measuring unit Screen Menu screen setup System Menu BACK SN : 00612 time Copy Menu Saving and calling up unit settings Page Mode Menu SPECTR. Text Menu Videotext Holding the videotext page Enlarging the videotext page Original videotext size Scope Menu BACK zoom + x zoom - x signal /noise rflev +0dB sample 1 Video scope menu Horizontal zoom Enlarging the video signal Scope Menu Measurement of the amplitude of the video signal Selecting the video line Measurement of video signals via the AV socket (SCART) rflev +0dB sample 1 Audio Scope Increasing time / unit y-pos Reducing time / unit Position of the audio signal DiSEqC Scope Increasing time / unit Reducing time / unit Saving function Position and triggering of the DiSEqC signal Level measurement of analogue signals Level measurement of digital signals Selecting the spectrum representation Span/DIV BW Span/DIV BW Span/DIV BW ANALOG marker DIGITAL marker C/N measurement of analogue signals in Sat operation C/N measurement of digital signals in Sat operation Cross-polarisation measurement on signals in SAT operation zoo m max off Colour representation of I/Q value pairs Constellation diagram for QPSK (DVB-S) Measurement of the bit error rate (BER) Measurement of signal noise ratio (SNR) Carrier offset QPSK no Page Examples for QPSK constellation diagrams Constellation diagram for QAM (DVB-C) Measurement of the bit error rate (BER) Measurement of modulation error rate (MER) Carrier offset Invers (no) Frontend locked Selecting the symbol rate (symbol-clock) Inverting /not inverting constellation diagram Zoom Examples for QAM constellation diagram Page Constellation diagram DVB-T (optional) Measurement of bit error rate (BER) Measurement of signal noise ration (SNR) Carrier offset Carrier mode Hierarchy Code rate Guard Invers Frontend locked Channel display Impulse response representation (Echo representation) (optional) Measuring principle TRACK. MVG10 <> mark reflv mvg10 only max off Comfortable upstream 4.080 MHz and Downstream 47860 MHz measurement Upstream measurement Downstream measurement Page Auto Measure BACK edit list set point stop on/off start measure input ListNo Display of the check point Modem / RS 232 interface Connection cable for modem / RS 232 Modem/RS232 menu Setting baud rate Setting local echo rate < > echo off r/cts off init < > Code (Password) Operating of the MSK 33 via modem The TTY mode the ANSI mode The log-in procedure Requesting help Page 94 List of the command abbreviations General commands Switch-over of the operating type of the MSK 33 Measurements with the MSK 33 Changing settings of the MSK 33 Page Maintenance, Storage and Customer Service Maintenance Unit calibration Exterior cleaning Interior cleaning Maintenance, Storage and Customer Service Printer paper-exchanging the ribbon Overview of DiSEqC commands Command overview framing byte Command overview address byte Command overview command byte Command overview data byte DiSEqC commands for Kathrein matrices Command for Kathrein matrix 9xx-series Command for Kathrein matrix EXR 20 Command for Kathrein matrix EXR 22 Channel tables Channel and frequency table standard B/G (frequency in MHz) Channel and frequency table standard L(frequency in MHz) Channel and frequency table standard D/K (frequency in MHz) Channel and frequency table standard I (frequency in MHz) Channel and frequency table standard M/N (frequency in MHz) Channel and frequency table standard M/N(frequency in MHz) Technical data Page Scope of delivery Accessories Assignment of the SCART socket Assignment of RS232 socket Assignment of socket TS PARALLEL (optional) Unit variants Downloading New MSK33 Operating Software General notes: