Kenwood TS-B2000, TS-2000X instruction manual Your First QSO HF/ 50 MHz band

YOUR FIRST QSO (HF/ 50 MHz band)

Are you ready to give your TS-2000(X) a quick try? Reading these two pages should get your voice on the air in your first QSO on the HF/ 50 MHz band shortly. The instructions below are intended only for a quick guide. If you encounter problems or there is something you don’t understand, read the detailed explanations given later in this manual.

RECEIVING

26

CW TUNE

9.6k STA CON

PF
F LOCK A
ATT	PRE

HF/VHF/UHF ALL MODE MULTI BANDER TS-2000

RIT

ALT

XIT

RIT/SUB

LEVEL	LEVEL
VOX
	PROC
	ANT1/2

CLEAR

P.C.T

SET

_

+

SEND	AT
PHONES	LEVEL
	N
	.
	R
	.
	LEVEL
	A
	.
	N
	.
MIC	MANUAL
	B
	.
	C
	.
	LO/
	WIDTH

CH1/REC	CH2/REC	CH3/REC
1	2
		3
TONE/SEL
	METER
		CTCSS/SEL
4	5
		6
NB/LEVEL
	AGC/OFF
7	8	FINE/STEP
		9
.
DCS/SEL	SHIFT/OFFSET
	0	ENT
	HI/
	SHIFT

C N U F

MAIN
	AUTO
CAR	LSB
MIC	USB
TX MONI	REV
PWR	CW
	FSK
DELAY	NAR
KEY	FM
	AM
CLR	SEL
DISP		1MHz

			SUB
	MENU		TF-
			SET
		MAIN	SUB
			SG.SEL
	CTRL	SCAN
8	5

	NUAL	BC	MAIN
			GAIN
	MA	RF
QUICK MEMO
MR	M.IN
C
CALL
.
IN
	TL
	SA
M/S	REV
		IN
	SPLIT
A/B		MA
	TRACE
VFO/CH			AF
	A=B
VFO/M
MG.SEL			L
			SQ
M VFO M.IN

3 1 7 1 4 1

MULTI	CH
SUB

Note: This section explains only keys and controls required to briefly try the transceiver.

qSet the following as specified:

•MAIN AF: Fully counterclockwise

•MAIN RF GAIN: Fully clockwise

•MAIN SQL: Fully counterclockwise

wSwitch ON the DC power supply, then press and hold [ ] (POWER) briefly on the transceiver.

•Do not press the switch for more than approximately 2 seconds; the transceiver will be switched OFF.

•Upon power up, “HELLO” appears, followed by the selected frequency and other indicators.

d

	1	3	5	7	9	20	40	60dB
S
		10		25	50		100W
PWR
ALC
					FILTER

eConfirm that VFO A has been selected for communications; “tA” should be visible on the display. If it has not, press [A/B] to select VFO A.

rTurn the MAIN AF control slowly clockwise until you hear a suitable level of background noise.

tPress [+] or [–]to select an HF/ 50 MHz

Amateur radio band.

yPress [LSB/ USB/ AUTO] or [FM/ AM/ NAR] to select an operating mode.

•To select the second mode on each key, press the same key again. For example, each press of [LSB/ USB/ AUTO] switches between LSB and USB modes.

uIf you have selected FM, turn the MAIN SQL control clockwise until the background noise is just eliminated; the MAIN band LED (above the [MIC/ CAR] key) turns off.

• With LSB or USB selected, skip this step.

iTurn the Tuning control to tune in a station.

•If you do not hear any stations, you may have the wrong antenna connector selected. Press [FUNC], [AT/ ANT1/2] to switch between the antenna 1 and 2 connectors.

4