Kenwood TS-2000X, TS-B2000 instruction manual Press LSB/ USB/ Auto , CW/ FSK, Are totally Selected

18 TROUBLESHOOTING

Problem	Probable Cause	Corrective Action	Page
			Ref.
No signals are	1 The SQL control is fully clockwise.	1 Turn the SQL control counterclockwise.	19
received or receive	2 The Attenuator function is ON.	2 Press [ATT/ F LOCK] to switch the	57
sensitivity seems		function OFF.
poor.	3 [SEND] was pressed, and the	3 Press [SEND] to return to receive	–
	transceiver is now in transmit mode.	mode. Or release Mic [PTT].
	Or, Mic [PTT] is pressed.
	4 The receive bandwidth was	4 Review “DSP FILTERS” and	55
	incorrectly set.	“CHANGING THE RECEIVE FILTER
		BANDWIDTH”, and set the controls
		accordingly.	72
	5 The wrong antenna connector	5 Press [FUNC], [AT/ ANT1/2] to select
	(ANT 1 or ANT 2) was selected.	the other antenna connector.	57
	6 The receive preamplifier is OFF.	6 Press [PRE/ LOCK A] to switch the
		function ON.
No signals are	The RF control was set too low.	Turn the MAIN RF GAIN control fully	18
received or receive		clockwise.
sensitivity seems
poor; S-meter is
reading full scale.
Received signals	The wrong modulation mode was	Press [LSB/ USB/ AUTO], [CW/ FSK/	19
are totally	selected.	REV], or [FM/ AM/ NAR] to select the
unintelligible.		correct modulation mode.
Memory Scan will	1 The SQL control was not set	1 Adjust the SQL controls to just	19,46
not start scanning.	correctly.	eliminate background noise.
	2 Less than two memory channels	2 Unlock at least two memory channels.	68
	were unlocked.
	3 Less than two memory channels	3 Store data in at least two memory	68
	were programmed.	channels.
	4 The SQL control was not set	4 Adjust the SQL controls.	19,46
	correctly.
Memory Scan will	With Group Scan selected, the channel	Select the group that contains the memory	69
not scan one of the	you want to scan is in a different group.	channel you want to scan.
stored channels; the
desired channel is
NOT locked out.
Program Scan will	The start and end frequencies are	Store different start and end frequencies.	62
not start scanning.	identical.
Tuning does not	The impedance of the coaxial cable and	Adjust the antenna system to lower the	1
finish successfully.	antenna was not matched.	SWR.
	Tuning does not successfully finish
	depending on conditions although the
	SWR meter indicates smaller than 3:1.
The internal tuner is	The SWR of the antenna system is too	Adjust the antenna system to lower the	1
bypassed	high.	SWR.
immediately after
tuning is started.
You cannot transmit	1 The microphone plug was not	1 Turn OFF the power, ensure the MIC	3
even though you	inserted completely into the MIC	connector has no foreign objects in it,
press Mic [PTT] or	connector.	then plug in the connector firmly.
transmissions result	2 The Transmit Inhibit function is ON.	2 Change Menu No. 54 to OFF.	41
in no contacts.	3 CW or FSK was selected instead of	3 Press [LSB/ USB/ AUTO] or [FM/ AM/	19
	a voice mode.	NAR] to select a voice mode.
	4 The DSP TX filter bandwidth was	4 Adjust the settings in Menu No. 22.	41
	inproperly selected.
	5 The wrong antenna connector	5 Press [FUNC], [ANT 1/2] to select the	72
	(ANT 1 or ANT 2) was selected.	other antenna connector.

101