Kenwood TS-B2000, TS-2000X Satellite Channel Name, Quick Memory in Satellite Mode

11 SPECIALIZED COMMUNICATIONS

3 Press [LSB/ USB/ AUTO] or [CW/ FSK/ REV] to				SATELLITE CHANNEL NAME
	select LSB, USB, or CW mode.			You can name each Satellite Memory channel using a
4 As the Satellite moves, fine tune to the changing
				maximum of 8 alpha-numeric characters. First, store
	downlink (RX) frequency of the satellite using the
				the settings to the Satellite Memory channel {above}.
	Tuning control (adjusting the Doppler effect).
				To store the Satellite Channel name:
	• As you adjust the downlink (RX) frequency, the			1 Press [M.IN] then turn the MULTI/ CH control to
	Trace function automatically changes the uplink
					select the Satellite Memory channel.
	frequency so that the sum of the two
	frequencies is kept the same (Reverse Trace).			2	Press [DISP].
	• If necessary, press [A=B / TRACE] to quit the			3	An entry cursor appears. Select a character by
	Trace function. “TRACE” disappears.				turning MULTI/ CH control, then move the cursor
	• The trace function can also change the uplink				using [SUB] or [MAIN]. You can also use the
	(TX) frequency so that the difference between				other methods to enter the characters. Refer to
	the two frequencies is kept the same (Normal				page 63 for details.
	Trace).			4 Press [M.IN] to store the name to the Satellite
5 If you want to switch to the normal trace mode,					Memory channel. Press [CLR] to quit.
	press [SPLIT / REV]. “R” disappears.			5 The stored Satellite Memory name appears on the
6 To adjust the frequency on the sub-band display					main dot-matrix display.
	(normally the uplink frequency) without tracing,
	turn the RIT/ SUB control. To adjust it using the			QUICK MEMORY IN SATELLITE MODE
	trace function, press [A/B / M/S] to swap the main
	band frequency and sub-band frequency then turn			While in the Satellite mode, only 1 Quick Memory
	the Tuning control or MULTI/ CH control. The
				channel is available. It uses Satellite Memory
	following table shows which control to use when
				channel 9 to store the settings. To store the settings
	adjusting frequencies with tracing ON and OFF.
				to the Quick Memory in Satellite mode, press QUICK
				MEMO [M.IN]. The settings are stored to Satellite
		TRACE/	TRACE/
				Memory channel 9.
		TRACE R ON	TRACE R OFF
	MAIN control	Main and Sub	Main	To recall the Quick Memory, press QUICK MEMO
	(Fine)			[MR] or select Satellite Memory channel 9, using the
	MULTI/ CH	Main and Sub	Main	MULTI/ CH control. Satellite Memory channel 9 is
	control (Coarse)			recalled.
	RIT/ SUB	Sub	Sub
	control			CHECKING THE UPLINK FREQUENCY
STORING SATELLITE MEMORY CHANNELS				When you need to monitor the uplink (TX) frequency,
				press [TF-SET]. Each time you press [TF-SET], the
You can store all the above settings to one of 10				uplink (TX) frequency and the downlink (RX)
				frequency are swapped.
Satellite memory channels for the future operations.
1 Press [M.IN], then turn the MULTI/ CH control to				USING XIT/ RIT IN SATELLITE MODE
	select a channel from 0 to 9.
2 Select your desired settings.				You can also use the RIT or XIT function while in the
3 Press [M.IN] again to store the selection to the				Satellite mode. Press [RIT/ CW TUNE] or [XIT/ ALT]
				to activate the function. When the RIT or XIT function
	memory channel. To quit, press [CLR].
				is ON, the sub-band frequency display shows the
Note: The Satellite Memory channel does not hold the frequency				current RIT or XIT offset frequency instead of the
				operating frequency. To clear the RIT or XIT offset
adjustment values when the channel is changed. So, when you
change the channel number or switch the transceiver OFF, the				frequency, press [CLEAR].
adjustment frequency values are cleared if they are not stored by
pressing [M.IN].				Note: You cannot activate both the RIT and XIT functions at the
				same time in the Satellite mode.

RECALLING A SATELLITE MEMORY CHANNEL

1Press [VFO/M / VFO/CH].

• The MULTI/ CH LED lights.

2Turn the MULTI/ CH control to select the desired Satellite Memory channel.

3Press [VFO/M / VFO/CH] to return to the frequency adjustment mode.

CHANGING THE FREQUENCY BAND

If you need to change the uplink and/or downlink frequency band, press [CTRL] to move the “” icon to the frequency band that you want to change. Then, press [+] or [–]to select the band you want to operate.

54