Control 2 values when OSC 1 Wave = Dwgs | Korg MICRO specs

Messages transmitted and received by the microKORG

Control 2 values when OSC 1 Wave = DWGS

When the synth parameter OSC 1 "WAVE" is set to DWGS, the "CONTROL 2" (knob 3 ) will select the DWGS waveform. The value of the control change transmitted/received by operating the "CONTROL 2" (knob 3 ) corresponds to the parameter value as follows.

	Value	DWGS Wave	Value	DWGS Wave
	(transmitted, received)	DWGS Wave	(transmitted, received)	DWGS Wave
	(transmitted, received)		(transmitted, received)
	0, 1	1	64, 65	33
	2, 3	2	66, 67	34
	4, 5	3	68, 69	35
	6, 7	4	70, 71	36
	8, 9	5	72, 73	37
	10, 11	6	74, 75	38
	12, 13	7	76, 77	39
	14, 15	8	78, 79	40
	16, 17	9	80, 81	41
	18, 19	10	82, 83	42
	20, 21	11	84, 85	43
	22, 23	12	86, 87	44
	24, 25	13	88, 89	45
	26, 27	14	90, 91	46
	28, 29	15	92, 93	47
	30, 31	16	94, 95	48
	32, 33	17	96, 97	49
	34, 35	18	98, 99	50
	36, 37	19	100, 101	51
	38, 39	20	102, 103	52
	40, 41	21	104, 105	53
	42, 43	22	106, 107	54
	44, 45	23	108, 109	55
	46, 47	24	110, 111	56
	48, 49	25	112, 113	57
	50, 51	26	114, 115	58
	52, 53	27	116, 117	59
	54, 55	28	118, 119	60
	56, 57	29	120, 121	61
	58, 59	30	122, 123	62
	60, 61	31	124, 125	63
	62, 63	32	126, 127	64

OSC 2 Semitone values

The value of the control change transmitted/received by operating OSC 2 "SEMITONE" (knob 3 ) of a synth program corresponds to the parameter value as follows.

Value (transmitted, received)		OSC 2 Semitone	Value (transmitted, received)		OSC 2 Semitone
0...	2	–24	66, 67		+1
3...	5	–23	68...	70	+2
6, 7		–22	71...	73	+3
8...	10	–21	74, 75		+4
11...	13	–20	76...	78	+5
14, 15		–19	79, 80		+6
16...	18	–18	81...	83	+7
19, 20		–17	84...	86	+8
21...	23	–16	87, 88		+9
24...	26	–15	89...	91	+10
27, 28		–14	92...	94	+11
29...	31	–13	95, 96		+12
32, 33		–12	97...	99	+13
34...	36	–11	100, 101		+14
37...	39	–10	102...	104	+15
40, 41		–9	105...	107	+16
42...	44	–8	108, 109		+17
45...	47	–7	110...	112	+18
48, 49		–6	113, 114		+19
50...	52	–5	115...	117	+20
53, 54		–4	118...	120	+21
55...	57	–3	121, 122		+22
58...	60	–2	123...	125	+23
61, 62		–1	126, 127		+24
63...	65	0

"SYNC NOTE" value when LFO 1/2 or DELAY "TEMPO SYNC" = ON

If "TEMPO SYNC" is ON, the parameter that is set by the LFO 1/2 "FREQUENCY" (knob 4 ) or the DELAY "DELAY TIME" (knob 3 ) will change to "SYNC NOTE." In this case, the value of the control change message transmitted by knob operations (or received) will correspond to the parameter value as shown below.

Value (transmitted, received)	LFO Sync Note	DELAY Sync Note
0...8	1/1	1/32
9...17	3/4	1/24
18...25	2/3	1/16
26...34	1/2	1/12
35...42	3/8	3/32
43...51	1/3	1/8
52...59	1/4	1/6
60...68	3/16	3/16
69...76	1/6	1/4
77...85	1/8	1/3
86...93	3/32	3/8
94...102	1/12	1/2
103...110	1/16	2/3
111...119	1/24	3/4
120...127	1/32	1/1

57

Image 63

Korg MICRO manual Control 2 values when OSC 1 Wave = Dwgs, OSC 2 Semitone values

Contents

Page Page Iii Table of Contents Table of Contents Midi on the microKORG Saving your edited settings Introduction Main Features Front panel Front and rear panel Timbre SELECT/FORMANT Hold key Edit Controls 1, 2, 3, 4, 5 knobsEdit Select 1 dial Edit Select 2 dial Rear panel Connections to the audio inputs Connecting the included micConnections Connections from the audio outputs Turning the power off Turning the power onPower supply Turning the power on Demo songs Listening to the demo songsMicroKORG contains several demo songs Modifying the sound Using the Performance Edit function to modify the soundSynth programs Selecting and playing a program Using the Pitch and MOD wheels for control Using the Octave Shift UP and Down keys for controlUsing the keyboard for control Knob 3 EG ATTACK, Knob 4 EG Release Vocoder programsPlaying a vocoder program Knob 1 CUTOFF, Knob 2 Resonance Modifying the arpeggio Using the arpeggiatorUsing the step arpeggiator to vary the arpeggio Arpeggiator Basic editing procedure Basic editingSelect the parameter that you want to edit If the parameter value does not change when you turn knobs How to read the pages for each section p.16To return to the original parameter values of a program Selecting the timbre to edit Using both timbres LayerEditing each timbre Listening to only one timbre Solo Editing a synth program Structure of a synth programOverview Unison Detune Voice SYNTH/VOCODERSINGLE/LAYER Voice Assign Pitch SYNTH/VOCODER Control Wave Sine Wave You can modify the waveform by adjusting this valueAdjusting this value will modify the waveform. Figure Triangle Wave Wave Control Processing an external input audio signal TUNE-63...63 Wave Saw, Square, TriangleOSC MOD SEMITONE-24...24 Mixer Synth OSC 1 LevelOSC 2 Level Noise Level 127 Resonance TypeDB LPF Figure CUTOFF0...127 Filter oscillation Filter KEY Track12dB BPF 12dB HPF Second note-on will start from a level Sustain Release EG ResetATTACK0...127 Decay Distortion AMP Amplifier SynthLEVEL0...127 Panpot L63...Center...R63 Sustain EG ResetAMP EG SYNTH/VOCODER Attack Wave LFO2 LFO 1, 11. LFO 2 SYNTH/VOCODERWave LFO1 Tempo Sync OFF, on Frequency Keyboard tracking keyboard posi- tion Patch 1, 13. Patch 2, 14. Patch 3, 15. Patch 4 SynthMOD INT Velocity keyboard playing strength Modulator Editing a vocoder programStructure of a vocoder program Carrier Editing example for a vocoder program OSC1 SYNTH/VOCODER HPF Level High-frequency portion of the signal will always be passedGate Sense THRESHOLD0...127 Mixer Vocoder Inst LevelNoise Level Filter Vocoder Formant ShiftSense FC MOD Vocoder Amp EG will be the modulation sourceINTENSITY-63...63 Direct Level AMP Vocoder CH 4 Level CH 1 LevelCH 2 Level CH 3 Level Modulation-type effect MOD FX Delay effect Delay FXEditing the effects and EQ MicroKORGs effect structure Specifies the speed of the modula- tion effect LFO MOD FX SYNTH/VOCODERSelects the effect type LFO Speed Tempo Sync Delay SYNTH/VOCODERDelay Time Delay Depth Sets the amount of boost or cut for EQ SYNTH/VOCODERLOW EQ Gain HI EQ Gain Structure of arpeggiator Editing the arpeggiator GATE0...100 Resolution 1/24...1/4ARPEG. a SYNTH/VOCODER TEMPO20...300 Last Step ARPEG. B SYNTH/VOCODERLatch KEY Sync Global structure Overall settings Global Audio in Thru Signal will not be output Signal will be output30.0...50.0 Position Using the microKORG with Other Midi devices Midi Connecting Midi devices/computersMidi on the microKORG MIDI-related settings Set the microKORGs Global Position to Pre TG Synchronizing the arpeggiator Midi Midi CHLocal Program change Messages transmitted and received by the microKORGMidi channels Pitch bend Parameters transmitted and received via Nrpn Gate values Other controlsControlling CH Param Realtime Messages System exclusive messages Front panel knob/key control change assignments OSC 2 Semitone values Control 2 values when OSC 1 Wave = Dwgs Saving a program Saving your edited settingsProcedure Saving Data Initializing a program Shift functionsCopying a timbre Exchanging timbres Midi Filter Midi FilterInitializing CH Level A/B Initializing CH PAN A/B Assigning control changes Control ChangeAssigning control changes Midi Data Dump Transmission procedureReception procedure Data dump Preload Restoring the factory settings Write protect settingRestoring the factory settings Write protect setting Timbre solo function Switch between Edit Select 1/2Enter demo mode Other Shift key functions Example 1. LFO1 LFO 1/2 and delay time synchronizationExample 2. Delay time Appendix Troubleshooting Specifications and options Index Symbols Index Korg INC Voice Name List Parameter List Shift Function List