137
Global
P0
P1 P2 P3 P4 P5 P6

0–1B: Change all bank references

This command changes all program banks specified for tim-
bres in combinations or tracks of songs.
1Select “Change all bank references” to access the dialog
box.
2If you wish to change bank references for combinations,
check “Combination.” If you wish to change bank refer-
ences for songs, check “Song.”
3In “Program Bank,” specify the replacement for each
bank.
4To execute the Change All Bank References command,
press the OK button. To cancel, press the Cancel button.
If you change two or more different banks to the same
bank, it will not be possible to use this function to
change them back to different banks. Be careful that the
change destination banks do not overlap.

0–1C: Touch Panel Calibration

If input via the LCD screen does not work as you expect, or
if the edit cell moves to a location other than where you
pressed the LCD screen, use this command to adjust the sen-
sitivity of the LCD screen.
1Select “Touch Panel Calibration” to access the dialog
box.
If you are unable to select this command from the page
menu, hold down the [ENTER] key and press the [2] key
to access the command.
2Press the square in the upper left of the LCD. When your
touch has been detected correctly the square will be high-
lighted.
3Press the square in the lower right of the LCD. When
your touch has been detected correctly the square will be
highlighted.
4Press the Done button.
If your touch was not detected correctly, an error mes-
sage will appear. Please perform the procedure once
again.

0–1D: Half Damper Calibration

If a damper pedal that supports half damper (the DS–1H
option) is connected to the DAMPER jack, here’s how you
can adjust the sensitivity if the damper effect is not applied
appropriately.
Since the half-damper pedal is highly sensitive, please
use the optional DS-1H. Other pedals may not produce
the appropriate effect, or may be impossible to calibrate
correctly.
1Connect a half-damper pedal to the DAMPER jack.
2Select “Half Damper Calibration” to access the dialog
box.
3Press the half-damper pedal, and then release your foot
from the pedal.
4Press the Done button.
If the adjustment could not be performed correctly, an
error message will be displayed. Please perform the pro-
cedure once again.
0–2: System Preference

0–2a: System Preference

Bank Map [KORG, GM(2)]

Specifies the mapping of programs and combinations rela-
tive to Bank Select control change messages (CC#0 upper
byte and CC#32 lower byte).
The bank select messages shown in the table below will be
received (R) and transmitted (T) for program banks INT-A–
INT-F, G, g(1)...g(9), g(d), EXB-A–EXB-G (INT-F is only for
the EXB-MOSS option) and Combination banks INT-A–INT-
E, and EXB-A–EXB-G.
Bank Bank Map: KORG Bank Map: GM(2)
INT-A 00. 00 R/T 63. 00 R/T
INT-B 00. 01 R/T 63. 01 R/T
INT-C 00. 02 R/T 63. 02 R/T
INT-D 00. 03 R/T 63. 03 R/T
INT-E 00. 04 R/T 63. 04 R/T
INT-F 00. 05 R/T 63. 05 R/T
G,
g(1)...g(9) 121. 00, 121. 01...09 R/T 121. 00, 121. 01...09 R/T
56. 00 R 56. 00 R
00. 00, 00. 01...(XG) R
00. 00, 01. 00...(GS) R
g(d) 120. 00 R/T 120. 00 R/T
62. 00 R 62. 00 R
63. 127 R (→Korg MUTE)
EXB-A 00. 08 R/T 63. 08 R/T
EXB-B 00. 09 R/T 63. 09 R/T
EXB-C 00. 10 R/T 63. 10 R/T
EXB-D 00. 11 R/T 63. 11 R/T
EXB-E 00. 12 R/T 63. 12 R/T
EXB-F 00. 13 R/T 63. 13 R/T
EXB-G 00. 14 R/T 63. 14 R/T
0–1
0–2a
0–2b