Show Server Characteristics, Show Services | Lantronix MSS100, 1-T

Interactive Connections

Using the MSS

5.2.3.7 Show Server Characteristics

This command displays network-related server identiÞcation information including the MSSÕs hardware address, node address, IP address, domain, any conÞgured gateways and nameservers, and the subnet mask. In addition, inactivity and retransmission limits, password restrictions, and the types of incoming logins permitted are shown.

5.2.3.8 Show Server Counters

This command enables the system administrator to view quantitative information about send and receive errors. It also displays error information for the Ethernet and TCP/IP protocols that can be used to diagnose network transmission problems.

5.2.3.9 Show Services

This command displays characteristics of LAT services offered on the network. Information shown includes service names, service ratings, group codes, offering nodes, service identiÞcation strings, and availability.

5.2.3.10 Show Sessions

This command displays information about current sessions including each active port, user, and type of session.

5.2.3.11 Show Users

This command displays the name, port number, and connection status of all current users, or a speciÞed user.

5 - 10

Image 42

Lantronix MSS100, 1-T2 manual Show Server Characteristics, Show Server Counters, Show Services, Show Sessions, Show Users

Contents

Serial Server Installation Guide Part Number Contents Contact Information Troubleshooting Pinouts Iii Page Introduction Terms Protocols Software Conﬁguration Configuration Introduction Installation MSS Components Installation MSS LEDs Installation Power-up Diagnostics Is It Working? 4Pinging the MSSPage Getting Started Using EZWebCon Using an ARP Entry and the Ping CommandIP Address Conﬁguration 1Entering ARP and Ping Unix Using a DHCP, BOOTP, or Rarp Reply Using the Serial Console Incoming Logins Controlling Incoming LoginsEZWebCon Login and Conﬁguration Incoming LAT Logins Serial Port LoginsOther Incoming TCP/IP Logins Rlogin Remote Console Logins Starting Outbound ConnectionsTelnet Logout 2 SPX3 LAT Privileged Password Command SetSystem Passwords Basic Conﬁguration Login Password Protocol Conﬁguration1 TCP/IP Parameters 2 IPX/SPX Parameters Serial Port Conﬁguration LAT Parameters Basic Configuration Serial Port Configuration Change Preferred SPX None Otherwise, only Telnet console port connections are possible Page Using the MSS Incoming ConnectionsSocket Connections LAT Connections 1.1 TCP/IP Socket Connections1.2 IPX/SPX Socket Connections Host Applications 4Reducing Flow Control Code Examples Local SwitchInteractive Connections Session Control Backward and Forward Switches 8DeÞning Switches Outgoing Connections Disconnect and ResumeSession Limits 10Connecting with Rlogin 2.3 SPX 12Connecting to a Service 2.4 LAT Status Displays Show Server Counters Show Server CharacteristicsShow Services Show Sessions Emulating a Direct Serial Connection Mssb Multihost Mode 1 Conﬁguring Multihost Mode 15Setting the MSS for Multihost Mode Multihost Mode Using the MSS Contact Information LANtronix Troubleshooting Problems and Error Messages Table B-1Problems and Error Messages, Bootp Troubleshooting Etc/services Þle? Tftp Troubleshooting Entering Commands at the Boot Prompt Figure B-1BCP Command Examples Entering Commands at the Boot Prompt Troubleshooting Modem Conﬁguration Checklist Page DB25 Connector RJ-45 ConnectorPinouts Modem Wiring DSR Data Signal Ready versus CD Carrier DetectDTR Data Terminal Ready Updating Software Obtaining New SoftwareVia FTP Via a Modem Figure D-1Lantronix FTP Session Reloading MSS Software Updating Software Reloading MSS Software Figure D-3Reloading Flash ROM using NetWare NetWare 2 TCP/IP 3 MOP Troubleshooting Flash ROM Updates Tftp Speciﬁcations Power SpeciﬁcationsTemperature Limitations Relative Humidity LimitationsPage Warranty Statement Declaration of Conformity EMC Index Index-i Loadhost 4-3, 5-9, B-6 Index-ii Telnet 1-4, 5-1 Index-iii