Is It Working?, 4Pinging the MSS | Lantronix MSS100, 1-T2 manual

Installation

Is It Working?

2.3 Is It Working?

If the MSS appears to be working and the unit is connected to the network, there are three ways to conÞrm that it is working correctly:

¥If there is a terminal attached, press the Return key and log in. If you are able to log in, the server is running normally.

¥If an IP address has been conÞgured for the MSS (see IP Address ConÞguration on page 3-2), ping the MSS from a TCP/IP host.

Figure 2-4:Pinging the MSS

unix% ping 192.0.1.233

When you are satisÞed that the MSS is working properly, proceed to Chapter 3, Getting Started. If the server does not boot properly, see Appendix B, Troubleshooting.

2 - 5

Image 15

Lantronix MSS100, 1-T2 manual Is It Working?, 4Pinging the MSS

Contents

Serial Server Installation Guide Part Number Contents Contact Information Troubleshooting Pinouts Iii Page Introduction Protocols Terms Conﬁguration Software Configuration Introduction MSS Components Installation MSS LEDs Installation Installation Power-up Diagnostics 4Pinging the MSS Is It Working?Page Getting Started Using EZWebCon Using an ARP Entry and the Ping CommandIP Address Conﬁguration 1Entering ARP and Ping Unix Using the Serial Console Using a DHCP, BOOTP, or Rarp Reply Incoming Logins Controlling Incoming LoginsEZWebCon Login and Conﬁguration Rlogin Serial Port LoginsOther Incoming TCP/IP Logins Incoming LAT Logins Remote Console Logins Starting Outbound ConnectionsTelnet Logout 2 SPX3 LAT Basic Conﬁguration Command SetSystem Passwords Privileged Password Login Password Protocol Conﬁguration1 TCP/IP Parameters 2 IPX/SPX Parameters LAT Parameters Serial Port Conﬁguration Basic Configuration Serial Port Configuration Change Preferred SPX None Otherwise, only Telnet console port connections are possible Page Using the MSS Incoming ConnectionsSocket Connections LAT Connections 1.1 TCP/IP Socket Connections1.2 IPX/SPX Socket Connections 4Reducing Flow Control Host Applications Session Control Local SwitchInteractive Connections Code Examples 8DeÞning Switches Backward and Forward Switches Outgoing Connections Disconnect and ResumeSession Limits 2.3 SPX 10Connecting with Rlogin 2.4 LAT 12Connecting to a Service Status Displays Show Sessions Show Server CharacteristicsShow Services Show Server Counters Mssb Emulating a Direct Serial Connection Multihost Mode 15Setting the MSS for Multihost Mode 1 Conﬁguring Multihost Mode Multihost Mode Using the MSS Contact Information LANtronix Problems and Error Messages Troubleshooting Table B-1Problems and Error Messages, Etc/services Þle? Bootp Troubleshooting Entering Commands at the Boot Prompt Tftp Troubleshooting Figure B-1BCP Command Examples Entering Commands at the Boot Prompt Troubleshooting Modem Conﬁguration Checklist Page DB25 Connector RJ-45 ConnectorPinouts Modem Wiring DSR Data Signal Ready versus CD Carrier DetectDTR Data Terminal Ready Updating Software Obtaining New SoftwareVia FTP Figure D-1Lantronix FTP Session Via a Modem Updating Software Reloading MSS Software Reloading MSS Software NetWare Figure D-3Reloading Flash ROM using NetWare 3 MOP 2 TCP/IP Tftp Troubleshooting Flash ROM Updates Relative Humidity Limitations Power SpeciﬁcationsTemperature Limitations SpeciﬁcationsPage Warranty Statement EMC Declaration of Conformity Index-i Index Index-ii Loadhost 4-3, 5-9, B-6 Index-iii Telnet 1-4, 5-1