Input, Output, and Machine Configuration | Lexicon 960L specification

Operations in DetailLexicon, Inc.

Control Mode: Clocks, Configuration, and System Screens, continued

Use the Right Navigation Arrow to get to the Rate			Wordclock Lock Status: A small padlock icon in the
display. For internal wordclock, you must select the			System Status Display shows lock status. If the
exact rate, as shown in Fig. 4-3. For external wordclock			wordclock becomes unlocked from the signal, the icon’s
via the BNC or AES inputs, you need only select			background flashes red (Figure 4-4) and the 960L
44.1/48 kHz or 88.2/96 kHz range. The 960L will then			outputs are muted. This lock indicator is visible in the
lock onto your source.			System Status Display during all operating modes.

Locked

Unlocked

Figure 4-4 — Locked and unlocked wordclock.

Input, Output, and Machine Configuration

The 960L is an 8-input/8-output device. Input sources can be either analog or AES digital, and all inputs must be the same input type. Each output is sent to both analog and AES digital outputs. For any configuration, the mapping of physical channels to algorithm channels is fixed. The CONFIG soft button brings up the screens for selecting the 960L’s I/O and machine configuration.

The number of machines available varies with the sample rate. At 44.1/48 kHz, the 960L can be configured as up to four machines. At 88.2/96 kHz, up

to two machines can be configured. Where multiple machines are available, each is programmed separately.

In stereo configurations (Figs. 4-5 and 4-6), all available machines are connected as two-channel in, two- channel out. Note that each machine is numbered and each machine’s I/O configuration is displayed in red at the lower right corner of its diagrammed block.

When you switch to a new Configuration, no Programs or Registers are yet loaded, so the Scribble Strip is blank and the Joystick Status Display is greyed out.

Figure 4-5 — Stereo configuration for 44.1/48 kHz sample rate; four machines available.

4-4

Image 32

Lexicon 960L owner manual Input, Output, and Machine Configuration, Locked and unlocked wordclock

Contents

960L. Digital Effects System Important Safety Instructions Table Of Contents Table Of Contents Introduction Title of Section Mainframe Description Rear PanelAbout the 960L Unpacking the 960L Clock Card Midi Connectors Five-pin DIN female Remote-Control ConnectorsMains Power Switch IEC Power Connector Standby Switch and Indicator Front PanelFloppy Drive Thumbscrews CPU Card Behind the Front PanelDSP-Card Slots Installation MountingVentilation Location Wordclock Connections Digital Audio ConnectionsMidi Connections LARC2 Remote Navigating Typical Display Screens Unpacking the Larc LARC2 RemoteAbout the LARC2 LARC2 Control Surface LARC2 Control Surface Getting What You Want LARC2 Connections Navigating Typical Display Screens A typical display screen Mode Faders Joystick About the Faders and Joystick Lexicon Button Audio IndicatorsFine Adjust Basic Operation AN Overview of the Controls Basic Operation An Overview of the Controls Setup Control Mode Quick Guide to Operation 960L Owner’s MaunalBasic Operations Quick Guide to Operation Machine Selection Program Loading Editing a Program or Register Storing Your Edits Name screen Info screens are similar Control Mode CLOCKS, Configuration Operations in Detail Loading Programs and Registers Loading Programs Programming Machines Loading RegistersAlternative Loading Techniques Control Mode Clocks, Configuration, and System Screens Wordclock Input, Output, and Machine Configuration Locked and unlocked wordclock 960L Owner’s Maunal Operations in Detail 44.1/48kHz Dual machines 5-in and 2-in Output Assignment Left Right Center Unused Surround Surround Analog and Digital I/O System Screen Fine Adjust EditingEditing Algorithms Editing With the Faders Editing with the Joystick Quick Comparisons via the Lexicon Button Editing Inputs and Outputs Input Panning Output Panning Avoiding Overload Setting Levels960L Surround Panning Rules From the Edit Algorithm, Inputs, Outputs Options screen Using the Edit Algorithm ScreenV-Page and Parameter Reassignment 22 Edit V-Page screen programming the joystick Naming and Annotating Storing and Labeling Your EditsStoring 25 a Register Info Options Enabled Organizing Your Registers Machine Mode Using the Floppy DriveCD-ROM Edit Tools for Registers Using the Reverb Programs Using the Reverb Programs Reverberation and Reality Using The Reverb Program Lexicon, Inc Reverberation and Reality Msec Sound in Space a Short History of Stereo and Surround Algorithms Random Hall Surround Hall ChamberPlate & Surround Plate Ambience & Surround Ambience Inverse Ambient ChamberReverse & Surround Reverse Parameters Used in the 960L Algorithms Using The Reverb ProgramLexicon, Inc FbckL FbckRFbckLF FbckLS LvLL LvRRLvLR LvRL LvLFLF RearRoll RearRvbRShape RSpread Size SlopeSpin Spread Midi Channel Usage Description NomenclatureMidi Channel Allocation Card Configuration Bank and Program MappingBank Description Program # Description 960Ls response Midi SysexIncoming Inquiry Midi Byte Description Midi Implementation Chart Specifications Specifications Connector 48K Rack Units96K Factory Programs LARC2 User Interface Appendix Appendix Program Descriptions Halls Appendix B1 P4 B3 P4 B6 P2 B7 P2 B9 P9 B11 P5 Empty Mini Chamber Similar to Snare Chamber, but even smaller Lg Brite Room Random Hall Simply large and bright Echo Plate Like Flat Plate, but with echoes Stereo Bank Kitchen Chamber Can you find your disposal sound effect?