Editing Inputs and Outputs, Input Panning | Lexicon 960L guide

960L Owner’s Maunal

Operations in Detail

Editing, Continued

Editing Inputs and Outputs

The LARC2’s joystick can be used to place any input or output signals anywhere in the soundfield. Input and output levels can also be set, using the faders. Input panning and level adjustments are not "Global"; they affect only the current Program or Register.

Input Panning

To edit inputs, press the EDIT key, then the INPUTS soft button, to bring up the screen shown in figure 4-16.

You can see from the System Status Display at the upper right that two machines are in use and you are editing the inputs for Machine 1. The Main Operating Display shows that the current machine has five inputs and where each input signal is positioned in the soundfield.

In figure 4-16, the Left Surround input, channel 4, is currently selected, so its header is highlighted and its pan position is indicated on the Joystick Map. The JOYSTICK key is off, so the joystick has not captured the parameter – note the separate positions of the cursor and the setting dot.

Input currently mapped to joystick

Input levels, now controlled by faders

Joystick position

Parameter currently controlled by joystick (not captured — JOYSTICK key off)

Figure 4-16 — Editing screen for input panning and levels, with joystick key off.


	Note new position of selected input		Joystick has captured parameter

Figure 4-17 — Editing screen for input panning, and levels after panning with joystick.

4-11

Image 39

Lexicon 960L owner manual Editing Inputs and Outputs, Input Panning

Contents

960L. Digital Effects System Important Safety Instructions Table Of Contents Table Of Contents Title of Section Introduction Mainframe Unpacking the 960L DescriptionRear Panel About the 960L IEC Power Connector Clock Card Midi Connectors Five-pin DIN femaleRemote-Control Connectors Mains Power Switch Thumbscrews Standby Switch and IndicatorFront Panel Floppy Drive Behind the Front Panel DSP-Card SlotsCPU Card Location InstallationMounting Ventilation Digital Audio Connections Midi ConnectionsWordclock Connections Navigating Typical Display Screens LARC2 Remote LARC2 Remote About the LARC2Unpacking the Larc LARC2 Control Surface LARC2 Control Surface LARC2 Connections Getting What You Want A typical display screen Navigating Typical Display Screens About the Faders and Joystick Mode Faders Joystick Audio Indicators Fine AdjustLexicon Button AN Overview of the Controls Basic Operation An Overview of the Controls Basic Operation Quick Guide to Operation Setup Control Mode 960L Owner’s MaunalBasic Operations Quick Guide to Operation Program Loading Machine Selection Storing Your Edits Editing a Program or Register Name screen Info screens are similar Operations in Detail Control Mode CLOCKS, Configuration Loading Programs Loading Programs and Registers Loading Registers Alternative Loading TechniquesProgramming Machines Wordclock Control Mode Clocks, Configuration, and System Screens Locked and unlocked wordclock Input, Output, and Machine Configuration 960L Owner’s Maunal Operations in Detail 44.1/48kHz Dual machines 5-in and 2-in Output Assignment Left Right Center Unused Surround Surround System Screen Analog and Digital I/O Editing With the Faders Fine AdjustEditing Editing Algorithms Quick Comparisons via the Lexicon Button Editing with the Joystick Input Panning Editing Inputs and Outputs Output Panning Setting Levels 960L Surround Panning RulesAvoiding Overload Using the Edit Algorithm Screen V-Page and Parameter ReassignmentFrom the Edit Algorithm, Inputs, Outputs Options screen 22 Edit V-Page screen programming the joystick Storing and Labeling Your Edits StoringNaming and Annotating Organizing Your Registers 25 a Register Info Options Enabled Edit Tools for Registers Machine ModeUsing the Floppy Drive CD-ROM Using the Reverb Programs Reverberation and Reality Using the Reverb Programs Using The Reverb Program Lexicon, Inc Reverberation and Reality Msec Sound in Space a Short History of Stereo and Surround Random Hall Algorithms Ambience & Surround Ambience Surround HallChamber Plate & Surround Plate Ambient Chamber Reverse & Surround ReverseInverse Parameters Used in the 960L Algorithms Using The Reverb ProgramLexicon, Inc FbckLS FbckLFbckR FbckLF LvRL LvLFLF LvLLLvRR LvLR RSpread RearRollRearRvb RShape Spread SizeSlope Spin Midi Nomenclature Midi Channel AllocationChannel Usage Description Program # Description Card ConfigurationBank and Program Mapping Bank Description Midi Sysex Incoming Inquiry Midi Byte Description960Ls response Midi Implementation Chart Specifications Specifications Factory Programs Connector48K Rack Units 96K LARC2 User Interface Appendix Halls Appendix Program Descriptions Appendix B1 P4 B3 P4 B6 P2 B7 P2 B9 P9 B11 P5 Empty Mini Chamber Similar to Snare Chamber, but even smaller Lg Brite Room Random Hall Simply large and bright Echo Plate Like Flat Plate, but with echoes Stereo Bank Kitchen Chamber Can you find your disposal sound effect?