Bank and Program Mapping, Bank Description | Lexicon 960L guide

MIDI	Lexicon, Inc.

MIDI, Continued

Program Loading

Because of the large number of potential Programs in the 960L, Program Change messages are used along with the Bank Select extension to provide MIDI Program selection. Controllers 0 and 32 are sent to the system, followed by a Program Change message to select a program. In this method, Controller 0 provides the most-significant 7 bits of the Bank and Controller 32 provides the least-significant 7 bits. The Program within a Bank is selected with a Program Change message. Each Bank has 10 programs or less, so only Program Changes 0 – 9 will cause a program load.

The Bank values are "sticky", that is, the 960L will remember the Bank values for each MIDI channel. It is not necessary to send a Bank change with each Program Change unless the Bank has indeed changed. This is in full conformance the MIDI specification.

Bank and Program Mapping

There are 10 Programs or fewer in each Bank. Bank and Program Changes out of range will be ignored.

Bank	Description

0-19	Factory Preset (Controller 0 = 0; Controller 32 = 0-19)

2048-2147	User Registers (Controller 0 = 16; Controller 32 = 0-99)

8192	Floppy Disk (Controller 0 = 64; Controller 32 = 0-9)

16383 (highest Bank)	Card configuration. For Channel 1 (DSP card) only.

Card Configuration

The DSP card is partitioned through Program Change messages on channel 1. The highest Bank number

(16383, 0x7f on Controller 0 and 0x7f on Controller 32) is used for this purpose. Other Bank numbers are reserved for future use. Here are the values:

Program #	Description

0	Stereo (4 stereo machines at 48K. 2 at 96K)

1	Surround (5-in/5-out plus 2-in/5-out at 48K. 5-in/5-out at 96K)

2	Surround (dual 2-in/5-out at 48K. Single 2-in/5-out at 96K)

63	8-channel. Useful for wiring checks and diagnostics.

Continuous Controllers

The 960L does not respond to continuous controllers, except those used for Bank change.

6-2

Image 64

Lexicon 960L Bank and Program Mapping, Bank Description, Card Configuration, Program # Description, Continuous Controllers

Contents

960L. Digital Effects System Important Safety Instructions Table Of Contents Table Of Contents Introduction Title of Section Mainframe Description Rear PanelAbout the 960L Unpacking the 960L Clock Card Midi Connectors Five-pin DIN female Remote-Control ConnectorsMains Power Switch IEC Power Connector Standby Switch and Indicator Front PanelFloppy Drive Thumbscrews DSP-Card Slots Behind the Front PanelCPU Card Installation MountingVentilation Location Midi Connections Digital Audio ConnectionsWordclock Connections LARC2 Remote Navigating Typical Display Screens About the LARC2 LARC2 RemoteUnpacking the Larc LARC2 Control Surface LARC2 Control Surface Getting What You Want LARC2 Connections Navigating Typical Display Screens A typical display screen Mode Faders Joystick About the Faders and Joystick Fine Adjust Audio IndicatorsLexicon Button Basic Operation AN Overview of the Controls Basic Operation An Overview of the Controls Setup Control Mode Quick Guide to Operation 960L Owner’s MaunalBasic Operations Quick Guide to Operation Machine Selection Program Loading Editing a Program or Register Storing Your Edits Name screen Info screens are similar Control Mode CLOCKS, Configuration Operations in Detail Loading Programs and Registers Loading Programs Alternative Loading Techniques Loading RegistersProgramming Machines Control Mode Clocks, Configuration, and System Screens Wordclock Input, Output, and Machine Configuration Locked and unlocked wordclock 960L Owner’s Maunal Operations in Detail 44.1/48kHz Dual machines 5-in and 2-in Output Assignment Left Right Center Unused Surround Surround Analog and Digital I/O System Screen Fine Adjust EditingEditing Algorithms Editing With the Faders Editing with the Joystick Quick Comparisons via the Lexicon Button Editing Inputs and Outputs Input Panning Output Panning 960L Surround Panning Rules Setting LevelsAvoiding Overload V-Page and Parameter Reassignment Using the Edit Algorithm ScreenFrom the Edit Algorithm, Inputs, Outputs Options screen 22 Edit V-Page screen programming the joystick Storing Storing and Labeling Your EditsNaming and Annotating 25 a Register Info Options Enabled Organizing Your Registers Machine Mode Using the Floppy DriveCD-ROM Edit Tools for Registers Using the Reverb Programs Using the Reverb Programs Reverberation and Reality Using The Reverb Program Lexicon, Inc Reverberation and Reality Msec Sound in Space a Short History of Stereo and Surround Algorithms Random Hall Surround Hall ChamberPlate & Surround Plate Ambience & Surround Ambience Reverse & Surround Reverse Ambient ChamberInverse Parameters Used in the 960L Algorithms Using The Reverb ProgramLexicon, Inc FbckL FbckRFbckLF FbckLS LvLL LvRRLvLR LvRL LvLFLF RearRoll RearRvbRShape RSpread Size SlopeSpin Spread Midi Midi Channel Allocation NomenclatureChannel Usage Description Card Configuration Bank and Program MappingBank Description Program # Description Incoming Inquiry Midi Byte Description Midi Sysex960Ls response Midi Implementation Chart Specifications Specifications Connector 48K Rack Units96K Factory Programs LARC2 User Interface Appendix Appendix Program Descriptions Halls Appendix B1 P4 B3 P4 B6 P2 B7 P2 B9 P9 B11 P5 Empty Mini Chamber Similar to Snare Chamber, but even smaller Lg Brite Room Random Hall Simply large and bright Echo Plate Like Flat Plate, but with echoes Stereo Bank Kitchen Chamber Can you find your disposal sound effect?