Manuals / Lexmark / Computer Equipment / Printer

Lexmark S510-2222-00 setup guide Verify printer setup, Turning on the printer

Models: S510-2222-00

1 94

Download 94 pages 38.07 Kb

Page 75

Step 8: Verify printer setup

Step 8: Verify printer setup

Turning on the printer

Note: To prevent an electrical overload, plug your printer into a well-grounded outlet on a non- ground fault interrupter (GFI) circuit.

1 Plug one end of the power cord into the socket on the side of the printer and the other end into a properly grounded outlet.

Verify printer setup 67

Image 75

Lexmark S510-2222-00 setup guide Verify printer setup, Turning on the printer

Contents

Infoprint Color Setup GuidePage Infoprint Color Setup GuideConventions Safety informationEdition October FCC emissions informationTable of contents Opening the top cover About your printer IntroductionPublications CD Other sources of informationUnpack your printer Step 1 Unpack your printerSetup Guide Publications CD Quick Reference and sleeve2 Unpack your printer Considering environmental issues Step 2: Select a location for your printerSelect a location for your printer 508 mm 4 Select a location for your printer734.9 mm 29 in 102 mm 5 in.152.1 mm 6 in 1241.8 mm1241.8 mm Network and internet printersSelect a location for your printer 869.2 mm 34.3 in 102 mm 5 in.152.1 mm 6 in56 in 6 Select a location for your printer869.2 mm 34.3 in 102 mm 5 in.329.5 mm 13 in 1241.8 mmSelect a location for your printer Printer with high-capacityfeeder8 Set up the printer and paper handling options TopicGo to page Set up the printer and paper handling options Installing the printer base or cabinet10 Set up the printer and paper handling options Installing a 550-sheetdrawerSet up the printer and paper handling options Positioning the printer12 Set up the printer and paper handling options Installing an optional duplex unit5 Slide in the duplex unit Set up the printer and paper handling options14 Set up the printer and paper handling options Tighten the thumbscrewsClose the duplex unit door Set up the printer and paper handling options Installing an optional high-capacityfeederAttaching the docking frame 16 Set up the printer and paper handling options3 Use the wrench to tighten the screws Set up the printer and paper handling optionsAttaching the guide rail and feeder 18 Set up the printer and paper handling optionsSet up the printer and paper handling options 4 Roll the high-capacityfeeder toward the printer and check the alignment of the pins with the holes in the docking frame20 Set up the printer and paper handling options Set up the printer and paper handling options Installing height adjustment spacersAdd or remove spacers To add spacers 22 Set up the printer and paper handling optionsSet up the printer and paper handling options Attaching the paper tray labelsStep 4 Install memory and option cards Removing the system board access cover24 Install memory and option cards 2 Slide the cover up and away from the printer Install memory and option cardsthe instructions you need 26 Install memory and option cardsTo install a 4 Use the following table to locateInstall memory and option cards Installing a memory card28 Install memory and option cards Installing a firmware card2 Unpack the firmware card Install memory and option cards30 Install memory and option cards Installing a hard diskFunction Installing an option cardInstall memory and option cards Card32 Install memory and option cards 1 Remove the system board access cover see pageInstall memory and option cards 4 Align the connector on the option card with the connector on the system board34 Install memory and option cards Reinstalling the system board access coverAttach cables Step 5: Attach cables36 Attach cables Attach cables Local printing2 Open the front door Step 6 Install printer supplies38 Install printer supplies To open the top cover3 Rotate the top cover locking lever to the left Install printer supplies5 Lift the top cover until it stops 40 Install printer suppliesInstalling the photodevelopers Install printer suppliesTransfer belt 4 Remove the tape from the photodeveloper 42 Install printer supplies6 While holding the photodeveloper with your left hand and the photodeveloper cover with your right hand, slide the photodeveloper in until the unit is fully seated Install printer supplies44 Install printer supplies Installing the toner cartridgesColored label Install printer supplies46 Install printer supplies Install printer supplies Attaching the Quick Reference booklet sleeve48 Install printer supplies Attaching an adhesive operator panel overlayas shown Closing the top coverInstall printer supplies Place both hands on the top cover4 Close the front door 50 Install printer supplies3 Rotate the top cover locking lever to the right bLift the top coverSource Step 7 Load paperLoad paper Go to52 Load paper Loading the paper trays1 Pull the paper tray out until it stops 2 Press the metal plate down until it locksLoad paper 54 Load paper 4 Release the paper guideLoad paper 6 Place the paper in the tray, print side down56 Load paper 9 Push the tray completely in the printerLoad paper Using the heavy media traySet the paper size PAPER MENU PAPER SIZE58 Load paper Set the paper typePAPER MENU PAPER TYPE PAPER MENU PAPER TYPELoad paper Loading the multipurpose feeder60 Load paper Load paper Note Do not exceed the maximum stack height. Overfilling the feeder may cause jams62 Load paper The multipurpose tray can be closed by lifting itLoad paper Loading the high- capacity feeder64 Load paper Load paper Note Do not exceed the maximum stack height. Overfilling the tray may cause paper jams66 Load paper 8 Press the Paper Tray buttonStep 8 Verify printer setup Turning on the printerVerify printer setup Printing a menu settings page 68 Verify printer setupUTILITIES MENU UTILITIES MENU Printing a network setup pageVerify printer setup What do I do next?Step 9 Configure for TCP/IP Setting the printer IP address70 Configure for TCP/IP Verifying the IP settings Configuring for Pull PrintingConfigure for TCP/IP Windows Step 10 Install printer driversNetwork printing 72 Install printer driversSupported printer drivers Creating ports and installing driversInstall printer drivers MacintoshOther network environments Installation instructions74 Install printer drivers Local printingInstall printer drivers Macintosh You must install the printer’s PPD and use it with the LaserWriter 8 printer driver or the Adobe PostScript driverPage Distribute information to users Step 11 Distribute information to usersIdentifying printer users Finding information78 Distribute information to users Distributing the information Storing the QuickCongratulations ReferenceIndex Index80 Index Index Page Please tell us how we can improve this book Infoprint Color Setup GuideReaders’ Comments - We’d Like to Hear from You Publication No. S510-2222-00Readers’ Comments - We’d Like to Hear from You BUSINESS REPLY MAILPage Part Number 53P7114 S510-2222-001P P/N 53P7114