Manuals / Lexmark / Computer Equipment / Printer

Lexmark S510-2222-00 Install memory and option cards, Removing the system board access cover

Models: S510-2222-00

1 94

Download 94 pages 38.07 Kb

Page 32

Step 4: Install memory and option cards

Step 4: Install memory and option cards

Removing the system board access cover

CAUTION! If you are installing memory or option cards after initial printer setup, turn the printer off and unplug the power cord. If you have any other devices connected to the printer, turn them off as well and unplug any cables going to the printer.

You can customize your printer memory capacity and connectivity by adding optional cards or hard disk.

You must remove the system board cover to install memory cards, a firmware card, a hard disk, or an option card.

You need a number 2 Phillips screwdriver to remove the system board cover.

Rear cover

24 Install memory and option cards

Image 32

Lexmark S510-2222-00 setup guide Install memory and option cards, Removing the system board access cover

Contents

Setup Guide Infoprint ColorPage Setup Guide Infoprint ColorSafety information Edition OctoberFCC emissions information ConventionsTable of contents Opening the top cover Introduction About your printerOther sources of information Publications CDStep 1 Unpack your printer Setup Guide Publications CDQuick Reference and sleeve Unpack your printer2 Unpack your printer Select a location for your printer Considering environmental issuesStep 2: Select a location for your printer 4 Select a location for your printer 734.9 mm 29 in 102 mm 5 in.152.1 mm 6 in1241.8 mm 508 mmNetwork and internet printers Select a location for your printer869.2 mm 34.3 in 102 mm 5 in.152.1 mm 6 in 1241.8 mm6 Select a location for your printer 869.2 mm 34.3 in 102 mm 5 in.329.5 mm 13 in1241.8 mm 56 inPrinter with high-capacityfeeder Select a location for your printerGo to page 8 Set up the printer and paper handling optionsTopic Installing the printer base or cabinet Set up the printer and paper handling optionsInstalling a 550-sheetdrawer 10 Set up the printer and paper handling optionsPositioning the printer Set up the printer and paper handling optionsInstalling an optional duplex unit 12 Set up the printer and paper handling optionsSet up the printer and paper handling options 5 Slide in the duplex unitClose the duplex unit door 14 Set up the printer and paper handling optionsTighten the thumbscrews Installing an optional high-capacityfeeder Set up the printer and paper handling options16 Set up the printer and paper handling options Attaching the docking frameSet up the printer and paper handling options 3 Use the wrench to tighten the screws18 Set up the printer and paper handling options Attaching the guide rail and feeder4 Roll the high-capacityfeeder toward the printer and check the alignment of the pins with the holes in the docking frame Set up the printer and paper handling options20 Set up the printer and paper handling options Installing height adjustment spacers Set up the printer and paper handling options22 Set up the printer and paper handling options Add or remove spacers To add spacersAttaching the paper tray labels Set up the printer and paper handling options24 Install memory and option cards Step 4 Install memory and option cardsRemoving the system board access cover Install memory and option cards 2 Slide the cover up and away from the printer26 Install memory and option cards To install a4 Use the following table to locate the instructions you needInstalling a memory card Install memory and option cardsInstalling a firmware card 28 Install memory and option cardsInstall memory and option cards 2 Unpack the firmware cardInstalling a hard disk 30 Install memory and option cardsInstalling an option card Install memory and option cardsCard Function1 Remove the system board access cover see page 32 Install memory and option cards4 Align the connector on the option card with the connector on the system board Install memory and option cardsReinstalling the system board access cover 34 Install memory and option cardsStep 5: Attach cables Attach cables36 Attach cables Local printing Attach cablesStep 6 Install printer supplies 38 Install printer suppliesTo open the top cover 2 Open the front doorInstall printer supplies 3 Rotate the top cover locking lever to the left40 Install printer supplies 5 Lift the top cover until it stopsTransfer belt Installing the photodevelopersInstall printer supplies 42 Install printer supplies 4 Remove the tape from the photodeveloperInstall printer supplies 6 While holding the photodeveloper with your left hand and the photodeveloper cover with your right hand, slide the photodeveloper in until the unit is fully seatedInstalling the toner cartridges 44 Install printer suppliesInstall printer supplies Colored label46 Install printer supplies Attaching the Quick Reference booklet sleeve Install printer suppliesAttaching an adhesive operator panel overlay 48 Install printer suppliesClosing the top cover Install printer suppliesPlace both hands on the top cover as shown50 Install printer supplies 3 Rotate the top cover locking lever to the rightbLift the top cover 4 Close the front doorStep 7 Load paper Load paperGo to SourceLoading the paper trays 52 Load paperLoad paper 1 Pull the paper tray out until it stops2 Press the metal plate down until it locks 4 Release the paper guide 54 Load paper6 Place the paper in the tray, print side down Load paper9 Push the tray completely in the printer 56 Load paperUsing the heavy media tray Set the paper sizePAPER MENU PAPER SIZE Load paperSet the paper type PAPER MENU PAPER TYPEPAPER MENU PAPER TYPE 58 Load paperLoading the multipurpose feeder Load paper60 Load paper Note Do not exceed the maximum stack height. Overfilling the feeder may cause jams Load paperThe multipurpose tray can be closed by lifting it 62 Load paperLoading the high- capacity feeder Load paper64 Load paper Note Do not exceed the maximum stack height. Overfilling the tray may cause paper jams Load paper8 Press the Paper Tray button 66 Load paperVerify printer setup Step 8 Verify printer setupTurning on the printer UTILITIES MENU Printing a menu settings page68 Verify printer setup Printing a network setup page Verify printer setupWhat do I do next? UTILITIES MENU70 Configure for TCP/IP Step 9 Configure for TCP/IPSetting the printer IP address Configure for TCP/IP Verifying the IP settingsConfiguring for Pull Printing Step 10 Install printer drivers Network printing72 Install printer drivers WindowsCreating ports and installing drivers Install printer driversMacintosh Supported printer driversInstallation instructions 74 Install printer driversLocal printing Other network environmentsMacintosh You must install the printer’s PPD and use it with the LaserWriter 8 printer driver or the Adobe PostScript driver Install printer driversPage Step 11 Distribute information to users Identifying printer usersFinding information Distribute information to usersDistributing the information Storing the Quick CongratulationsReference 78 Distribute information to usersIndex Index80 Index Index Page Infoprint Color Setup Guide Readers’ Comments - We’d Like to Hear from YouPublication No. S510-2222-00 Please tell us how we can improve this bookBUSINESS REPLY MAIL Readers’ Comments - We’d Like to Hear from YouPage 1P P/N 53P7114 Part Number 53P7114S510-2222-00