Manuals / Lexmark / Computer Equipment / Printer

Lexmark S510-2222-00 Reinstalling the system board access cover, Install memory and option cards

Models: S510-2222-00

1 94

Download 94 pages 38.07 Kb

Page 42

Reinstalling the system board access cover

Reinstalling the system board access cover

Screw slot

After you have finished installing cards on the printer system board, you must reinstall the system board access cover.

1 Align the holes on the access cover with the screws on the printer as shown.

2 Place the cover against the printer and slide it down.

3 Tighten the eight screws.

34 Install memory and option cards

Image 42

Lexmark S510-2222-00 setup guide Reinstalling the system board access cover, Install memory and option cards

Contents

Setup Guide Infoprint ColorPage Setup Guide Infoprint ColorFCC emissions information Safety informationEdition October ConventionsTable of contents Opening the top cover Introduction About your printerOther sources of information Publications CDQuick Reference and sleeve Step 1 Unpack your printerSetup Guide Publications CD Unpack your printer2 Unpack your printer Considering environmental issues Step 2: Select a location for your printerSelect a location for your printer 1241.8 mm 4 Select a location for your printer734.9 mm 29 in 102 mm 5 in.152.1 mm 6 in 508 mm869.2 mm 34.3 in 102 mm 5 in.152.1 mm 6 in Network and internet printersSelect a location for your printer 1241.8 mm1241.8 mm 6 Select a location for your printer869.2 mm 34.3 in 102 mm 5 in.329.5 mm 13 in 56 inPrinter with high-capacityfeeder Select a location for your printer8 Set up the printer and paper handling options TopicGo to page Installing the printer base or cabinet Set up the printer and paper handling optionsInstalling a 550-sheetdrawer 10 Set up the printer and paper handling optionsPositioning the printer Set up the printer and paper handling optionsInstalling an optional duplex unit 12 Set up the printer and paper handling optionsSet up the printer and paper handling options 5 Slide in the duplex unit14 Set up the printer and paper handling options Tighten the thumbscrewsClose the duplex unit door Installing an optional high-capacityfeeder Set up the printer and paper handling options16 Set up the printer and paper handling options Attaching the docking frameSet up the printer and paper handling options 3 Use the wrench to tighten the screws18 Set up the printer and paper handling options Attaching the guide rail and feeder4 Roll the high-capacityfeeder toward the printer and check the alignment of the pins with the holes in the docking frame Set up the printer and paper handling options20 Set up the printer and paper handling options Installing height adjustment spacers Set up the printer and paper handling options22 Set up the printer and paper handling options Add or remove spacers To add spacersAttaching the paper tray labels Set up the printer and paper handling optionsStep 4 Install memory and option cards Removing the system board access cover24 Install memory and option cards Install memory and option cards 2 Slide the cover up and away from the printer4 Use the following table to locate 26 Install memory and option cardsTo install a the instructions you needInstalling a memory card Install memory and option cardsInstalling a firmware card 28 Install memory and option cardsInstall memory and option cards 2 Unpack the firmware cardInstalling a hard disk 30 Install memory and option cardsCard Installing an option cardInstall memory and option cards Function1 Remove the system board access cover see page 32 Install memory and option cards4 Align the connector on the option card with the connector on the system board Install memory and option cardsReinstalling the system board access cover 34 Install memory and option cardsStep 5: Attach cables Attach cables36 Attach cables Local printing Attach cablesTo open the top cover Step 6 Install printer supplies38 Install printer supplies 2 Open the front doorInstall printer supplies 3 Rotate the top cover locking lever to the left40 Install printer supplies 5 Lift the top cover until it stopsInstalling the photodevelopers Install printer suppliesTransfer belt 42 Install printer supplies 4 Remove the tape from the photodeveloperInstall printer supplies 6 While holding the photodeveloper with your left hand and the photodeveloper cover with your right hand, slide the photodeveloper in until the unit is fully seatedInstalling the toner cartridges 44 Install printer suppliesInstall printer supplies Colored label46 Install printer supplies Attaching the Quick Reference booklet sleeve Install printer suppliesAttaching an adhesive operator panel overlay 48 Install printer suppliesPlace both hands on the top cover Closing the top coverInstall printer supplies as shownbLift the top cover 50 Install printer supplies3 Rotate the top cover locking lever to the right 4 Close the front doorGo to Step 7 Load paperLoad paper SourceLoading the paper trays 52 Load paper1 Pull the paper tray out until it stops 2 Press the metal plate down until it locksLoad paper 4 Release the paper guide 54 Load paper6 Place the paper in the tray, print side down Load paper9 Push the tray completely in the printer 56 Load paperPAPER MENU PAPER SIZE Using the heavy media traySet the paper size Load paperPAPER MENU PAPER TYPE Set the paper typePAPER MENU PAPER TYPE 58 Load paperLoading the multipurpose feeder Load paper60 Load paper Note Do not exceed the maximum stack height. Overfilling the feeder may cause jams Load paperThe multipurpose tray can be closed by lifting it 62 Load paperLoading the high- capacity feeder Load paper64 Load paper Note Do not exceed the maximum stack height. Overfilling the tray may cause paper jams Load paper8 Press the Paper Tray button 66 Load paperStep 8 Verify printer setup Turning on the printerVerify printer setup Printing a menu settings page 68 Verify printer setupUTILITIES MENU What do I do next? Printing a network setup pageVerify printer setup UTILITIES MENUStep 9 Configure for TCP/IP Setting the printer IP address70 Configure for TCP/IP Verifying the IP settings Configuring for Pull PrintingConfigure for TCP/IP 72 Install printer drivers Step 10 Install printer driversNetwork printing WindowsMacintosh Creating ports and installing driversInstall printer drivers Supported printer driversLocal printing Installation instructions74 Install printer drivers Other network environmentsMacintosh You must install the printer’s PPD and use it with the LaserWriter 8 printer driver or the Adobe PostScript driver Install printer driversPage Finding information Step 11 Distribute information to usersIdentifying printer users Distribute information to usersReference Distributing the information Storing the QuickCongratulations 78 Distribute information to usersIndex Index80 Index Index Page Publication No. S510-2222-00 Infoprint Color Setup GuideReaders’ Comments - We’d Like to Hear from You Please tell us how we can improve this bookBUSINESS REPLY MAIL Readers’ Comments - We’d Like to Hear from YouPage Part Number 53P7114 S510-2222-001P P/N 53P7114