Options/Accessories | Lincoln Electric 5000 instruction

C-1	ACCESSORIES	C-1

OPTIONS/ACCESSORIES

LINCOLN ELECTRIC ACCESSORIES

The following options/accessories are available for your POWER ARC 5000 from your local Lincoln Distributor.

Accessory Set (K875) – Includes the following:

•Twenty feet (6.1 meters) of #6 AWG electrode cable

•Fifteen feet (4.6 meters) of #6 work cable

•Headshield with No. 10 filter

•Work clamp

•Insulated electrode holder

•Sample electrodes

The cables are rated at 150 amps, 40% duty cycle.

Spark Arrester (K883-2)– A field-installed kit for the 11 HP Briggs & Stratton engine.

Rotor Removal Kit (S20925) – A service kit for removing the generator rotor from the tapered engine crankshaft.

BRIGGS AND STRATTON ACCESSORIES

The following options/accessories are available for your POWER ARC 5000 from your local Briggs & Stratton Distributor.

Exhaust Deflector (B&S No.393761) - Used to deflect engine exhaust down. Attaches to the muffler with four screws.

POWER ARC 5000

Image 36

Lincoln Electric 5000 manual Options/Accessories, Lincoln Electric Accessories, Briggs and Stratton Accessories

Contents

Power ARC Safety Depends on You Safety California Proposition 65 Warnings Electric Shock can kill Welding Sparks can cause fire or explosion Iii Précautions DE Sûreté Sûreté Pour Soudage a L’Arc Thank You Please Examine Carton and Equipment For Damage Immediately Table of Contents Installation Technical Specifications Power ARC Safety Precautions Location and VentilationStoring Stacking TiltingLifting Assembly of Wheels and Handle to the Tube Frame PRE-OPERATION Engine Service OILFuel Spark Arrester Electrical Output Connections Welding Cable Connections Auxiliary Power Receptacles Cable InstallationMachine Grounding Power Cord Connections to TWIST- Lock Plugs Premises WiringPlugs and HAND-HELD Equipment Circuit Breakers These Devices Without Safety Instructions OperationOperating Instructions General Description Recommended Applications Welding CapabilityLimitations Controls and Settings GENERATOR/WELDER Controls Figure B.2 Gasoline Engine Controls Gasoline Engine Controls Engine Operation Before Starting the EngineStarting the Engine Stopping the Engine BREAK-IN PeriodFor a HOT Engine For Best Engine Starting To USE the Generator AS AN Auxiliary Power Supply Generator OperationGeneral Information Table B.3 Generator Power Applications Suggested Power Applications Running Watts Start-up Watts To USE the Power ARC 5000 for Stick Welding Welding OperationControl Function / Operation Current Control Dial After YOU Finish the Weld Welding Guidelines Stick Welding What Happens in the Arc? Figure B.4 The welding arc Correct Welding Position Correct Arc Length Correct Way to Strike An ArcCorrect Welding Speed Practice Common MetalsTypes of Welds Penetration Fillet WeldsMultiple Pass Welds Welding in the Vertical Position Vertical-Up Welding Vertical-Down Welding How to Hardface the Sharp Edge Metal to Ground Wear Overhead WeldingWelding Sheet Metal Hardfacing To Reduce Wear Welding Cast Iron Cast Iron Plate Preparation Selecting Electrodes Out-of-Position Group AWS E6011High-Speed Group AWS E6013 Low Hydrogen Group Stable-Arc E7018 Accessories OPTIONS/ACCESSORIESLincoln Electric Accessories Briggs and Stratton Accessories Maintenance Routine and Periodic MaintenanceEngine Maintenance Engine Adjustments Figure D.3 Clean Cooling System Clean AIR Filter PRE-CLEANER Table D.2 Engine Maintenance Parts Part Part Number GENERATOR/WELDER Maintenance Figure D.6. Brush Removal and Replacement Figure D.7. Major Component Locations Troubleshooting SymptomsPossible Areas Generator POWER, Always Not RUN Engine Without AN Diagrams Wiring Diagram Power ARC Dimension Print How To Read Shop Drawings New Lessons in Arc WeldingNeed Welding Training? Basic Course Precaucion Warnung