Manuals / Lincoln Electric / Power Tools / Welder

Lincoln Electric SVM167-A service manual Control Board Replacement, Procedure

Models: SVM167-A

1 99

Download 99 pages 53.14 Kb

Page 64

Section TOC

Master TOC

F-28

TROUBLESHOOTING AND REPAIR

F-28

CONTROL BOARD REPLACEMENT (continued)

PROCEDURE

Return to

Return to

1.Remove power to the machine.

2.Using a 5/16” nutdriver, remove the three screws securing the tool tray.

3.Locate the control board.

4.Disconnect all associated plugs and leads connected to the control board.

5.Depress the retaining pins on the sides of the four nylon mounts to release the control board. See Figure F.8.

6.Carefully remove the control board.

7.Mount the new board to the nylon mounting pins.

8.Reconnect any plugs or leads previously removed.

9.Replace the tool tray previously removed.

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

FIGURE F.8. - CONTROL BOARD MOUNTING PINS

DEPRESS

LOCKING TAB ON

MOUNTING PIN

POWER MIG® 215

Image 64

Lincoln Electric SVM167-A service manual Control Board Replacement, Procedure

Contents

Power MIG Safety Depends on YouSafety California Proposition 65 WarningsElectric Shock can kill ARC Rays can burn Can be dangerousCylinder may explode if damaged Welding and Cutting Sparks can cause fire or explosionIii Précautions DE Sûreté Sûreté Pour Soudage a L’ArcMaster Table of Contents for ALL Sections Table of Contents Installation SECTION Installation Technical Specifications Power MIGSafety Precautions Uncrating the Power MIGInstallation LocationOutput Polarity Connections GUN and Cable Installation AUXILIARY POWER RECEPTACLESShielding GAS Cylinder may explode if damagedPower MIG Operation SECTION OPERATIONB-2 Wear eye, ear and body protec- tionOperation Wire Reel Loading READI-REELS, Spools or Coils Procedure for Changing Drive AND IDLE Roll SetsTo Start the Welder Idle Roll Pressure Setting Feeding Wire ElectrodeWire Drive Configuration Making a Weld Figure B.2bAvoiding Wire Feeding Problems Wire Feed Overload ProtectionFAN Control Input Line Voltage VariationsPower MIG Accessories SECTION Accessories 3ACCESSORIESC-3 InstalledMaking a Weld with the Spool GUN Adapter KIT and Spool GUNPower MIG Maintenance SECTION Maintenance Liner Removal and Replace Ment Table D.1GUN Handle Disassembly English Metric Description SizeFigure D.2 Major Component Locations Power MIG Line Switch Theory of Operation SECTION Figure E.2 Input Power Circuit Theory of OperationOutput Rectification Contactor and Control Board Figure E.3 Control CircuitsControl BOARD, GUN Trigger and Wire Drive Motor Figure E.4 Optional CircuitsProtective Devices and Circuits Wirefeed Overload ProtectionThermal and Overload Protection Power MIG TROUBLESHOOTING AND REPAIR SECTION Troubleshooting and Repair How To Use Troubleshooting GuidePC Board Troubleshooting Procedures Perform the Main Transformer Perform the Output Contactor Avoid contact with any portion These capacitors is toxicYour body Function Problems Wire Speed Potentiometer Test Welding Problems Weld bead is narrow or ropy Make sure the welding proce Test Description Main Transformer TestMaterials Needed ON/OFF Power Switch will be hot during these tests Test ProcedureMain Transformer Test X10 Table F.1. Test Points Input Voltage Test PointsWire Drive Motor and Wire Speed Potentiometer Test Black White1109 a Test for Feedback Voltage to Control BoardVDC Power MIG Output Bridge Rectifier Test Negative Lead Output Bridge Rectifier TestContactor Test Contactor Test Figure F.7. Contactor Terminals and LeadsVolts 10.0 Typical Output Voltage Waveform Machine Loaded MAX TAP GVolts 20.0 Normal Open Circuit Voltage Waveform MAX TAP GMachine Loaded to 180 Amps AT 16 VDC Scope Settings Volts 20.0 Control Board Replacement DescriptionControl Board Replacement ProcedureWire Drive Motor Assembly Replacement Wire Drive Wire Drive Motor Assembly ReplacementBolt Gas Hose TOC Output Diode Bridge Rectifier Replacement Output Diode Bridge Rectifier Mounting Bracket Mounting Bolts Rectifier Power MIG Output Capacitors Replacement Output Capacitors Replacement Figure F.14. Capacitor Bank LocationLead Mounting Bolts Nuts Lock washers 3 places Power MIG 41TROUBLESHOOTING and Repair F-41 Main Transformer ReplacementMain Transformer Replacement See Figure F.17Replacement Figure F.17. Leads X9, X10, 104B,104C, & H1BX2 X3 X4 X5 X6 X7 Lead Power MIG FAN BLADE/MOTOR Replacement FAN BLADE/MOTOR Replacement Perform the Output Capacitor Bank Removal ProcedureOutput Contactor Replacement Output Contactor Replacement Figure F.24Mounting Bolts Retest After Repair Electrical Diagrams Table of Contents Electrical Diagrams SectionPower MIG 215 208/220/230V POWEr miGPower MIG 215 208/220/230V for Codes 11099 SchEmaTic cOmplETE machiNE cODE 11247 l12308 pG1 L12308SchEmaTic cOmplETE machiNE cODE 11247 l12308 pG2 ElEcTrical DiaGramS ElEcTrical DiaGramS ElEcTrical DiaGramS ElEcTrical DiaGramS ElEcTrical DiaGramS ElEcTrical DiaGramS