Installation | Lincoln Electric SVM167-A specs

TOC

TOC

A-2

INSTALLATION

A-2

TECHNICAL SPECIFICATIONS – POWER MIG® 215

INPUT – SINGLE PHASE ONLY

Return to Section

Return to Master

Standard Voltage/Phase/Frequency

208/230/1/50/60 Hz

Duty Cycle 30% 40% 60%

Welding Current Range

30 – 250Amps

Input Current @ 170 Amp Rated Output (With 115V receptacle loaded to 15A)

39/35 Amps

RATED OUTPUT

Amps

215Amps

190Amps

170Amps

OUTPUT

Maximum Open Circuit Voltage

35 Volts

Input Current @ 215 Amp Rated Output (With 115V receptacle loaded to 15A)

45/41 Amps

Volts at Rated Amperes

22Volts

23Volts

24Volts

Welding Voltage Range

13.5-24 Volts

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

	RECOMMENDED INPUT WIRE AND FUSE SIZES

			75°C Copper Wire	75°C Copper Wire
		Input Ampere	in Conduit	in Conduit
Input Voltage/	Fuse or Breaker	Rating On	AWG (IEC) Sizes	AWG (IEC) Sizes
			(For lengths	(For lengths
Frequency (Hz)	Size (Super Lag)	Nameplate	up to 100 ft.)	exceeding 100 ft.)

208/50/60	60	45A	10 (6 mm2)	8 (10 mm2)
230/50/60	60	41A	10 (6 mm2)	8 (10 mm2)

NOTE: Use #10 AWG Grounding Wire

WIRE SPEED RANGE

Wire Speed50 – 700 IPM (1.27 – 17.8 m/minute)

PHYSICAL DIMENSIONS

Height	Width	Depth	Weight
31.79 in	18.88 in	38.78 in	210 Ibs
808 mm	480 mm	985 mm	95 kg

TEMPERATURE RANGES

OPERATING TEMPERATURE RANGE	STORAGE TEMPERATURE RANGE
-4°F to 104°F(-20°C to +40°C)	-40°F to 185°F(-40°C to +40°C)

POWER MIG® 215

Image 8

Lincoln Electric SVM167-A service manual Installation, Technical Specifications Power MIG

Contents

Power MIG Safety Depends on You Safety California Proposition 65 Warnings Electric Shock can kill ARC Rays can burn Can be dangerous Iii Welding and Cutting Sparks can cause fire or explosionCylinder may explode if damaged Précautions DE Sûreté Sûreté Pour Soudage a L’Arc Master Table of Contents for ALL Sections Table of Contents Installation SECTION Installation Technical Specifications Power MIG Safety Precautions Uncrating the Power MIGInstallation Location Output Polarity Connections GUN and Cable Installation AUXILIARY POWER RECEPTACLESShielding GAS Cylinder may explode if damaged Power MIG Operation SECTION OPERATIONB-2 Wear eye, ear and body protec- tion Operation To Start the Welder Procedure for Changing Drive AND IDLE Roll SetsWire Reel Loading READI-REELS, Spools or Coils Wire Drive Configuration Feeding Wire ElectrodeIdle Roll Pressure Setting Making a Weld Figure B.2b Avoiding Wire Feeding Problems Wire Feed Overload ProtectionFAN Control Input Line Voltage Variations Power MIG Accessories SECTION Accessories 3ACCESSORIESC-3 InstalledMaking a Weld with the Spool GUN Adapter KIT and Spool GUN Power MIG Maintenance SECTION Maintenance Liner Removal and Replace Ment Table D.1 GUN Handle Disassembly English Metric Description Size Figure D.2 Major Component Locations Power MIG Line Switch Theory of Operation SECTION Figure E.2 Input Power Circuit Theory of Operation Output Rectification Contactor and Control Board Figure E.3 Control Circuits Control BOARD, GUN Trigger and Wire Drive Motor Figure E.4 Optional Circuits Thermal and Overload Protection Wirefeed Overload ProtectionProtective Devices and Circuits Power MIG TROUBLESHOOTING AND REPAIR SECTION Troubleshooting and Repair How To Use Troubleshooting Guide PC Board Troubleshooting Procedures Perform the Main Transformer Perform the Output Contactor Your body These capacitors is toxicAvoid contact with any portion Function Problems Wire Speed Potentiometer Test Welding Problems Weld bead is narrow or ropy Make sure the welding proce Materials Needed Main Transformer TestTest Description Main Transformer Test Test ProcedureON/OFF Power Switch will be hot during these tests X10 Table F.1. Test Points Input Voltage Test Points Wire Drive Motor and Wire Speed Potentiometer Test Black White VDC Test for Feedback Voltage to Control Board1109 a Power MIG Output Bridge Rectifier Test Negative Lead Output Bridge Rectifier Test Contactor Test Contactor Test Figure F.7. Contactor Terminals and Leads Volts 10.0 Typical Output Voltage Waveform Machine Loaded MAX TAP G Volts 20.0 Normal Open Circuit Voltage Waveform MAX TAP G Machine Loaded to 180 Amps AT 16 VDC Scope Settings Volts 20.0 Control Board Replacement Description Control Board Replacement Procedure Wire Drive Motor Assembly Replacement Wire Drive Wire Drive Motor Assembly Replacement Bolt Gas Hose TOC Output Diode Bridge Rectifier Replacement Output Diode Bridge Rectifier Mounting Bracket Mounting Bolts Rectifier Power MIG Output Capacitors Replacement Output Capacitors Replacement Figure F.14. Capacitor Bank Location Lead Mounting Bolts Nuts Lock washers 3 places Power MIG 41TROUBLESHOOTING and Repair F-41 Main Transformer Replacement Main Transformer Replacement See Figure F.17 Replacement Figure F.17. Leads X9, X10, 104B,104C, & H1B X2 X3 X4 X5 X6 X7 Lead Power MIG FAN BLADE/MOTOR Replacement FAN BLADE/MOTOR Replacement Perform the Output Capacitor Bank Removal Procedure Output Contactor Replacement Output Contactor Replacement Figure F.24 Mounting Bolts Retest After Repair Electrical Diagrams Table of Contents Electrical Diagrams Section Power MIG 215 208/220/230V POWEr miG Power MIG 215 208/220/230V for Codes 11099 SchEmaTic cOmplETE machiNE cODE 11247 l12308 pG1 L12308 SchEmaTic cOmplETE machiNE cODE 11247 l12308 pG2 ElEcTrical DiaGramS ElEcTrical DiaGramS ElEcTrical DiaGramS ElEcTrical DiaGramS ElEcTrical DiaGramS ElEcTrical DiaGramS