Annunciate Trouble Indication

With this option box checked, the Console will announce three system trouble conditions if they occur: Console low battery, sensor low battery, and no sensor status. Sensor troubles type are announced followed by the sensor zone number. The default is to not annunciate these conditions.

✓NOTE FOR UL APPLICATIONS: UL requires the Annunciation Trouble Indication option to be enabled (option box checked).

Annunciate Status with Home Button

A short press of the HOME button will cause the Console to announce the Console’s time, current mode, and any trouble conditions. The default for status annunciations is enabled. Optionally, status annunciations can be disabled by un-checking this option box.

Annunciate Phone-Line/AC Status

If the telephone line is disconnected, or the AC power to the Console fails, the Console can annunciate these conditions. These annunciations will clear when the condition is corrected.

The default sets these types of annunciations to ANNUNCIATE ONCE. Alternately, use the this option to select OFF or ANNUNCIATE EVERY HOUR. Regardless of this setting, the Console records the condition in the event log and can report AC power failure to the monitoring service (if AC reporting is enabled).

✓NOTE:To prevent disturbing the subscriber, these annunciations will be suppressed while the Console is in Night Mode

Clock Annunciation Format

Both 12-hour (AM/PM) and 24-hour (“military”) time formats are supported in time announcements for Console status and reminder messages.

The default sets the time annunciations to 12-HOUR CLOCK format. Alternately, use the this option to select 24-HOUR CLOCK format.

Data version

Displays the version number of the Console’s data for factory use and troubleshooting.

Console Conﬁguration Misc.

Displays conﬁ guration numbers of the Console for factory use and troubleshooting.

Temperature Limit Settings

The Console contains a built-in sensor that constantly monitors the room temperature. The system can report and annunciate if the current room temperature measured is higher or lower than programmed temperature limits.

The Console will announce the high or low temperature alert every minute until the room temperature is within the programmed acceptable limits.

The temperature limit alert is enabled by default. Select DISABLE to turn off this feature or select ENABLE HOME MODE ONLY to sound and report temperature alerts only while the Console is in Home Mode.

The default set-point for the low-temp alert is 40°F (4.4°C).

The default set-point for the high-temp alert is 90°F (32.2°C).

To change the temperature set-points, enter new values (in Fahrenheit) into the HIGH TEMP and/or LOW TEMP ﬁ ll-in ﬁ elds.

A TWO-WAY AUDIO check box is available to select if a temperature alert starts a 2-way audio session with the monitoring station. The check box is selected by default. Alternately, un-check this box to inhibit 2-way audio after a temperature alert.

Language Selection

The Console can annunciate voice prompts in English or Spanish to guide the user during operation, and guide the installer during programming.

The two resident languages in the Console are English (EN) and Spanish (ES). Choose the active language for the Console using the radio buttons in the Language Selection area.

To use a different language, the language vocabulary ﬁle must ﬁrst be downloaded and installed in the Console’s ﬁrmware (See Section 15.2).

Console Time Settings

The Console contains a built-in clock and calendar, and supports automatic daylight saving time adjustment. The Console’s current time and date setting and the daylight saving information is displayed on the Console tab or the RA4200 software.

To change these settings, use the CONSOLE TIME function on the COMMUNICATION menu (or press the CONSOLE TIME icon on the toolbar ribbon). See Section 11.3.

✓NOTE: If the UMTS-3G cellular module is installed, the Console’s time will be set automatically over the air by the network.

Activity Windows

The activity timer is a feature that requires the subscriber to press the Console’s HOME button or activate a activity reset transmitter during one or two preset time windows to prevent an inactivity alarm from being reported.

Two activity time windows can be set. Each time window can be enabled or disabled, and has a start and stop time.

•To enable Activity Window 1 and/or Activity Window 2, check the enable box next to the start and stop times.

•Set the start time for the activity window.

•Set the stop time for the activity window.

Night Mode

Night Mode is an option that will suspend all Console supervisory and reminder annunciations during the Night Mode time window. This mode allows the user to sleep without interruptions from the Console about non-emergency conditions.

•To enable the Night Mode time window, check the enable box next to the start and stop times.

•Set the start time for Night Mode.

•Set the stop time for Night Mode.

Linear PERS-4200 Series manual Annunciate Trouble Indication, Annunciate Status with Home Button

Models: PERS-4200 Series