Chapter 5 | Configuration Using the |
DNS Server The IP address of your ISP’s server that |
| Click Save Settings to save your changes. Click Cancel | ||||||
| ||||||||
translates the names of websites into IP addresses. This |
| Changes to cancel your changes. |
|
| ||||
setting can be configured from the Setup tab’s Network |
| Setup > Zoom |
|
| ||||
Settings screen. |
|
|
| |||||
Default Gateway The IP address (default 0.0.0.0) of the |
| The Zoom screen depicts the status of all the ports in the | ||||||
gateway router between the Switch and management |
| system. This screen displays a | ||||||
stations on other network segments. This setting can be |
| Switch. The color of each switch port indicates its status: | ||||||
configured from the Setup tab’s Network Settings screen. |
| Green This port has a connection. |
|
| ||||
|
|
|
|
|
| |||
|
|
|
| Gray This port has no connection. |
|
| ||
| NOTE: The Default Gateway cannot be |
|
|
| ||||
| configured if the system IP address is set to |
| Orange The administrator has closed down this port. |
|
| |||
| 192.168.1.254. (The system IP Address is set |
|
|
| ||||
|
|
|
|
|
|
| ||
| using Setup > Network Settings.) |
|
|
|
|
|
| |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
Address Mode Specifies whether the Switch’s IP address |
|
|
|
|
|
| ||
is Static or dynamically assigned using DHCP (Dynamic |
|
|
|
|
|
| ||
Host Configuration Protocol). This setting can be |
|
|
|
|
|
| ||
configured from the Setup tab’s Network Settings screen. |
|
|
|
|
|
| ||
The default setting is Static. |
|
|
|
|
|
| ||
Base MAC Address Displays the Switch’s MAC address. |
|
|
|
|
|
| ||
Jumbo Frame This setting enables or disables Jumbo |
|
|
|
|
|
| ||
frames on the Switch. A maximum packet size of 9 KB is |
|
|
|
|
|
| ||
supported. Jumbo frames allow data to be transmitted |
|
|
|
|
|
| ||
using fewer frames, providing lower overhead, quicker |
|
|
|
|
|
| ||
|
|
|
|
|
| |||
processing time, and fewer interruptions. Select either |
|
|
| Setup > Zoom |
|
| ||
Enable or Disable (default). |
| Clicking on a port displays the Port Configuration screen. | ||||||
|
|
|
| |||||
| NOTE: The Jumbo Frame feature functions only |
|
|
|
|
|
| |
|
|
|
| NOTE: The port colors in the Zoom screen are | ||||
| on the Gigabit ports |
|
|
| ||||
|
|
|
|
|
| not related to the colors of the port LEDs. The | ||
|
|
|
| |||||
Switch Mode After Reset This setting specifies the |
|
|
| port LEDs display different status information, | ||||
|
|
| as described in “Chapter 2: Overview.” |
|
| |||
system mode following a system reset. Select either |
|
|
|
|
| |||
|
|
|
|
|
| |||
Standalone or Stackable (default). |
|
|
|
|
|
| ||
System Information |
| Setup > Network Settings |
|
| ||||
|
|
|
|
|
| |||
Model Name Displays the model name of the Switch. |
|
|
|
|
|
| ||
|
|
|
|
|
| |||
Hardware Version Displays the current hardware version. |
|
|
|
|
|
| ||
Boot Version Displays the current boot version. |
|
|
|
|
|
| ||
Firmware Version Displays the current software version |
|
|
|
|
|
| ||
System Location Displays the location of the system if it |
|
|
|
|
|
| ||
has been defined. This setting can be configured from the |
|
|
|
|
|
| ||
Setup tab’s Network Settings screen. |
|
|
|
|
|
| ||
System Contact The name of the administrator appears |
|
|
|
|
|
| ||
here, if one has been defined.This setting can be configured |
|
|
|
|
|
| ||
from the Setup tab’s Network Settings screen. |
|
|
|
|
|
| ||
System Up Time Displays the length of time that has |
|
|
|
|
|
| ||
elapsed since the Switch was last reset. |
|
|
|
|
|
| ||
Current Time Displays the current time. This setting can |
|
|
|
|
|
| ||
be configured from the Setup tab’s Time screen. |
|
|
|
|
|
| ||
|
|
| Setup > Network Settings |
|
| |||
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| 16 | |
